The NMI watchdog implementation assumes that the local APIC timer interrupt is
happening. This assumption is not longer true when high resolution timers and
dynamic ticks come into play, as they may switch off the local APIC timer
completely. Take the PIT/HPET interrupts into account too, to avoid false
positives.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <ak@suse.de>
Cc: Zachary Amsden <zach@vmware.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rohit Seth <rohitseth@google.com>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The local apic timer calibration has two problem cases:
1. The calibration is based on readout of the PIT/HPET timer to detect the
wrap of the periodic tick. It happens that a box gets stuck in the
calibration loop due to a PIT with a broken readout function.
2. CoreDuo boxen show a sporadic PIT runs too slow defect, which results
in a wrong lapic calibration. The PIT goes back to normal operation once
the lapic timer is switched to periodic mode.
Both are existing and unfixed problems in the current upstream kernel and
prevent certain laptops and other systems from booting Linux.
Rework the code to address both problems:
- Make the calibration interrupt driven. This removes the wait_timer_tick
magic hackery from lapic.c and time_hpet.c. The clockevents framework
allows easy substitution of the global tick event handler for the
calibration. This is more accurate than monitoring jiffies. At this point
of the boot process, nothing disturbes the interrupt delivery, so the
results are very accurate.
- Verify the calibration against the PM timer, when available by using the
early access function. When the measured calibration period is outside of
an one percent window, then the lapic timer calibration is adjusted to the
pm timer result.
- Verify the calibration by running the lapic timer with the calibration
handler. Disable lapic timer in case of deviation.
This also removes the "synchronization" of the local apic timer to the global
tick. This synchronization never worked, as there is no way to synchronize
PIT(HPET) and local APIC timer. The synchronization by waiting for the tick
just alignes the local APIC timer for the first events, but later the events
drift away due to the different clocks. Removing the "sync" is just
randomizing the asynchronous behaviour at setup time.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Zachary Amsden <zach@vmware.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rohit Seth <rohitseth@google.com>
Cc: Andi Kleen <ak@suse.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add clockevent drivers for i386: lapic (local) and PIT/HPET (global). Update
the timer IRQ to call into the PIT/HPET driver's event handler and the
lapic-timer IRQ to call into the lapic clockevent driver. The assignement of
timer functionality is delegated to the core framework code and replaces the
compile and runtime evalution in do_timer_interrupt_hook()
Use the clockevents broadcast support and implement the lapic_broadcast
function for ACPI.
No changes to existing functionality.
[ kdump fix from Vivek Goyal <vgoyal@in.ibm.com> ]
[ fixes based on review feedback from Arjan van de Ven <arjan@infradead.org> ]
Cleanups-from: Adrian Bunk <bunk@stusta.de>
Build-fixes-from: Andrew Morton <akpm@osdl.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With Ingo Molnar <mingo@elte.hu>
Add functions to provide dynamic ticks and high resolution timers. The code
which keeps track of jiffies and handles the long idle periods is shared
between tick based and high resolution timer based dynticks. The dyntick
functionality can be disabled on the kernel commandline. Provide also the
infrastructure to support high resolution timers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With Ingo Molnar <mingo@elte.hu>
Add broadcast functionality, so per cpu clock event devices can be registered
as dummy devices or switched from/to broadcast on demand. The broadcast
function distributes the events via the broadcast function of the clock event
device. This is primarily designed to replace the switch apic timer to / from
IPI in power states, where the apic stops.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With Ingo Molnar <mingo@elte.hu>
The tick-management code is the first user of the clockevents layer. It takes
clock event devices from the clock events core and uses them to provide the
periodic tick.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Architectures register their clock event devices, in the clock events core.
Users of the clockevents core can get clock event devices for their use. The
clockevents core code provides notification mechanisms for various clock
related management events.
This allows to control the clock event devices without the architectures
having to worry about the details of function assignment. This is also a
preliminary for high resolution timers and dynamic ticks to allow the core
code to control the clock functionality without intrusive changes to the
architecture code.
[Fixes-by: Ingo Molnar <mingo@elte.hu>]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The apic code is quite unstructured and missing a lot of comments.
- Restructure the code into helper functions, timer, setup/shutdown,
interrupt and power management blocks.
- Fixup comments.
- Namespace fixups
- Inline helpers for version and is_integrated
- Combine the ack_bad_irq functions
No functional changes.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Zachary Amsden <zach@vmware.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rohit Seth <rohitseth@google.com>
Cc: Andi Kleen <ak@suse.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow early access to the power management timer by exposing the verified read
function and providing a helper function which checks the pmtmr_ioport
variable and returns either the pm timer readout or 0 in case the pm timer is
not available.
Create a new header file and replace also the ifdef'ed extern definition in
arch/i386/kernel/acpi/boot.c
This is a preperatory patch for the rework of the local apic timer
calibration.
No functional changes.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a preperatory patch for highres/dyntick:
- replace the big #ifdef ARCH_APICTIMER_STOPS_ON_C3 hackery by functions
- remove the double switch in the power verify function (in the worst case
we switched ipi to apic and 20usec later apic to ipi)
- keep track of the the state which stops local APIC timer
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Len Brown <len.brown@intel.com>
Cc: <linux-acpi@vger.kernel.org>
Cc: Andi Kleen <ak@suse.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
apic.h does not get included on UP compiles. That way the
APICTIMER_STOPS_ON_C3 is not there and UP boxen have no support for timer
broadcasting. This was never noticed, because the lapic timer is only used
for profiling on UP.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the initial hrtimers.txt document to the new directory
"Documentation/hrtimers"
Add design notes for the high resolution timer and dynamic tick functionality.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reintroduce ktimers feature "optimized away" by the ktimers review process:
remove the curr_timer pointer from the cpu-base and use the hrtimer state.
No functional changes.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reintroduce ktimers feature "optimized away" by the ktimers review process:
multiple hrtimer states to enable the running of hrtimers without holding the
cpu-base-lock.
(The "optimized" rbtree hack carried only 2 states worth of information and we
need 4 for high resolution timers and dynamic ticks.)
No functional changes.
Build-fixes-from: Andrew Morton <akpm@osdl.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Improve kernel/hrtimers.c locking: use a per-CPU base with a lock to control
locking of all clocks belonging to a CPU. This simplifies code that needs to
lock all clocks at once. This makes life easier for high-res timers and
dyntick.
No functional changes.
[ optimization change from Andrew Morton <akpm@osdl.org> ]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- hrtimers did not use the hrtimer_restart enum and relied on the implict
int representation. Fix the prototypes and the functions using the enums.
- Use seperate name spaces for the enumerations
- Convert hrtimer_restart macro to inline function
- Add comments
No functional changes.
[akpm@osdl.org: fix input driver]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For CONFIG_NO_HZ we need to calculate the next timer wheel event based on a
given jiffie value. Extend the existing code to allow the extra 'now'
argument. Provide a compability function for the existing implementations to
call the function with now == jiffies. (This also solves the racyness of the
original code vs. jiffies changing during the iteration.)
No functional changes to existing users of this infrastructure.
[ remove WARN_ON() that triggered on s390, by Carsten Otte <cotte@de.ibm.com> ]
[ made new helper static, Adrian Bunk <bunk@stusta.de> ]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When searching for the next pending timer in the timer wheel we need to take
the cascade into account. The current code has several problems:
1. it looks into the previous cascade
2. it ignores a pending cascade
3. it ignores multiple cascades
Change the cascade lookup, so it calculates the array index from the point of
the next cascade and always look at the cascade buckets, when the cascade is
pending, i.e. gets executed in the next timer softirq. When multiple
cascades are pending, then lookup the next buckets too.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Uninline irq_enter(). [dynticks adds more stuff to it]
No functional changes.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Geode can safely use the TSC for highres, since:
1) Does not support frequency scaling,
2) The TSC _does_ count when the CPU is halted. Furthermore, the Geode
supports a mode called "suspension on halt", where Suspend mode (which
interacts with the power management states) is entered. TSC counting
during suspend mode is controlled by bit 8 of the Bus Controller
Configuration Register #0 (thanks Tom!).
3) no SMP :)
Check if "RTSC counts during suspension" and remove the requirement for
verification, so the clocksource code can safely select it as an timesource
for the highres timers subsystem.
Signed-off-by: Marcelo Tosatti <marcelo@kvack.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The TSC needs to be verified against another clocksource. Instead of using
hardwired assumptions of available hardware, provide a generic verification
mechanism. The verification uses the best available clocksource and handles
the usability for high resolution timers / dynticks of the clocksource which
needs to be verified.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The clocksource code allows direct updates of the rating of a given
clocksource now. Change TSC unstable tracking to use this interface and
remove the update callback.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixup the is_contionous replacement by a flag field.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixup the is_contionous replacement by a flag field.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixup the is_contionous replacement by a flag field.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixup the is_contionous replacement by a flag field.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Using a flag filed allows to encode more than one information into a variable.
Preparatory patch for the generic clocksource verification.
[mingo@elte.hu: convert vmitime.c to the new clocksource flag]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
make the TSC synchronization code more robust, and unify it between x86_64 and
i386.
The biggest change is the removal of the 'fix up TSCs' code on x86_64 and
i386, in some rare cases it was /causing/ time-warps on SMP systems.
The new code only checks for TSC asynchronity - and if it can prove a
time-warp (if it can observe the TSC going backwards when going from one CPU
to another within a critical section), then the TSC clock-source is turned
off.
The TSC synchronization-checking code also got moved into a separate file.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enqueue clocksources in rating order to make selection of the clocksource
easier. Also check the match with an user override at enqueue time.
Preparatory patch for the generic clocksource verification.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The delayed work code in arch/i386/kernel/tsc.c is an unused leftover of the
GTOD conversion. Remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prevent timeout overflow if timer ticks are behind jiffies (due to high
softirq load or due to dyntick), by limiting the valid timeout range to
MAX_LONG/2.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix multiple conversion bugs in msecs_to_jiffies().
The main problem is that this condition:
if (m > jiffies_to_msecs(MAX_JIFFY_OFFSET))
overflows if HZ is smaller than 1000!
This change is user-visible: for HZ=250 SUS-compliant poll()-timeout
value of -20 is mistakenly converted to 'immediate timeout'.
(The new dyntick code also triggered this, that's how we noticed.)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are loads of fat functions hidden in jiffies.h. Uninline them. No code
changes.
[jeremy@goop.org: export fix]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Distangle the NTP update from HZ. This is necessary for dynamic tick enabled
kernels.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Provide funtions to:
- check, whether an interrupt can set the affinity
- pin the interrupt to a given cpu
Necessary for the ability to setup clocksources more flexible (e.g. use the
different HPET channels per CPU)
[akpm@osdl.org: alpha build fix]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a flag so we can prevent the irq balancing of an interrupt. Move the
bits, so we have room for more :)
Necessary for the ability to setup clocksources more flexible (e.g. use the
different HPET channels per CPU)
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
arch/i386/kernel/built-in.o: In function `vmi_stop_hz_timer':
: undefined reference to `next_timer_interrupt'
If CONFIG_NO_HZ, next_timer_interrupt() doesn't exist (and presumably doesn't
make sense).
Perhaps VMI shouildn't be playing with timer internals at this level.
Cc: Zachary Amsden <zach@vmware.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A previous cleanup misused need_poll, which had a fairly broken interface.
It implemented a growable array, changing the used elements count itself,
but leaving it up to the caller to fill in the actual elements, including
the entire array if the array had to be reallocated. This worked because
the previous users were switching between two such structures, and the
elements were copied from the inactive array to the active array after
making sure the active array had enough room.
maybe_sigio_broken was made to use need_poll, but it was operating on a
single array, so when the buffer was reallocated, the previous contents
were lost.
This patch makes need_poll implement more sane semantics. It merely
assures that the array is of the proper size and that the contents are
preserved. It is up to the caller to adjust the used elements count and to
ensure that the proper elements are resent.
This manifested itself as a hang in 2.6.20 as the uninitialized buffer
convinced UML that one of its own file descriptors didn't support SIGIO and
needed to be watched by poll in a separate thread. The result was an
interrupt flood as control traffic over this descriptor sparked interrupts,
which resulted in more control traffic, ad nauseum.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If prepare_write or commit_write return AOP_TRUNCATED_PAGE we jump to
"retry" label and than if find_or_create_page() failed function return
incorrect error code.
Signed-off-by: Dmitriy Monakhov <dmonakhov@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It appears that the pcim_iomap_regions() function doesn't get the error
handling right. It BUGs early at boot with a backtrace along the lines of:
ahci_init
pci_register_driver
driver_register
[...]
ahci_init_one
pcim_iomap_region
pcim_iounmap
The following patch allows me to boot. Only the if(mask..) continue;
part fixes the problem actually, the gotos where changed so that we
don't try to unmap something we couldn't map anyway.
Signed-off-by: Frederik Deweerdt <frederik.deweerdt@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Small updates to the GPIO documentation, addressing feedback and
fixing a few spelling errors.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This modifies drivers/ata/sata_vsc.c to only set the cache line size
to 0x80 if the default value is zero. Apparently zero isn't allowed
due to a bug in the chip, but I've found performance is much better
with the (non-zero) default instead of 0x80.
[note1: "default" means BIOS-programmed value, in this context -jgarzik]
[note2: superfluous braces were removed from the patch -jg]
Signed-off-by: Nate Dailey <nate.dailey@stratus.com>
Signed-off-by: Jeremy Higdon <jeremy@sgi.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ADMA-capable controllers provide a bit in the status register that appears
to indicate that the controller detected an SError condition. Update sata_nv
to detect this and trigger error handling in order to handle the fault.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The hald media changed polling does really confuse things.
Noone knows why the delays are needed, but they give us access to the CD.
An udelay(50) will give reliable access to the drive, but there is still
one (or more) EH reset. The drive works without EH resets with udelay(100).
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If an ATA drive uses legacy mode, ata driver will choose 14 and 15
as the fixed irq number. On ia64 platform, such numbers are GSI and
should be converted to irq vector.
Below patch against kernel 2.6.20 fixes it.
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Ingo Molnar