You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
115 lines
5.6 KiB
115 lines
5.6 KiB
Qualcomm Technologies, Inc.
|
|
|
|
mdss-dsi is the master DSI device which supports multiple DSI host controllers
|
|
that are compatible with MIPI display serial interface specification.
|
|
|
|
DSI Controller:
|
|
Required properties:
|
|
- compatible: Should be "qcom,dsi-ctrl-hw-v<version>". Supported
|
|
versions include 1.4, 2.0 and 2.2.
|
|
eg: qcom,dsi-ctrl-hw-v1.4, qcom,dsi-ctrl-hw-v2.0,
|
|
qcom,dsi-ctrl-hw-v2.2, qcom,dsi-ctrl-hw-v2.3,
|
|
qcom,dsi-ctrl-hw-v2.4
|
|
And for dsi phy driver:
|
|
qcom,dsi-phy-v0.0-hpm, qcom,dsi-phy-v0.0-lpm,
|
|
qcom,dsi-phy-v1.0, qcom,dsi-phy-v2.0,
|
|
qcom,dsi-phy-v3.0, qcom,dsi-phy-v4.0
|
|
- reg: Base address and length of DSI controller's memory
|
|
mapped regions.
|
|
- reg-names: A list of strings that name the list of regs.
|
|
"dsi_ctrl" - DSI controller memory region.
|
|
"mmss_misc" - MMSS misc memory region.
|
|
- cell-index: Specifies the controller instance.
|
|
- clocks: Clocks required for DSI controller operation.
|
|
- clock-names: Names of the clocks corresponding to handles. Following
|
|
clocks are required:
|
|
"mdp_core_clk"
|
|
"iface_clk"
|
|
"core_mmss_clk"
|
|
"bus_clk"
|
|
"byte_clk"
|
|
"pixel_clk"
|
|
"core_clk"
|
|
"byte_clk_rcg"
|
|
"pixel_clk_rcg"
|
|
- gdsc-supply: phandle to gdsc regulator node.
|
|
- vdda-supply: phandle to vdda regulator node.
|
|
- vcca-supply: phandle to vcca regulator node.
|
|
- interrupt-parent phandle to the interrupt parent device node.
|
|
- interrupts: The interrupt signal from the DSI block.
|
|
|
|
Bus Scaling Data:
|
|
- qcom,msm-bus,name: String property describing MDSS client.
|
|
- qcom,msm-bus,num-cases: This is the number of bus scaling use cases
|
|
defined in the vectors property. This must be
|
|
set to <2> for MDSS DSI driver where use-case 0
|
|
is used to remove BW votes from the system. Use
|
|
case 1 is used to generate bandwidth requestes
|
|
when sending command packets.
|
|
- qcom,msm-bus,num-paths: This represents number of paths in each bus
|
|
scaling usecase. This value depends on number of
|
|
AXI master ports dedicated to MDSS for
|
|
particular chipset.
|
|
- qcom,msm-bus,vectors-KBps: A series of 4 cell properties, with a format
|
|
of (src, dst, ab, ib) which is defined at
|
|
Documentation/devicetree/bindings/arm/msm/msm_bus.txt.
|
|
DSI driver should always set average bandwidth
|
|
(ab) to 0 and always use instantaneous
|
|
bandwidth(ib) values.
|
|
|
|
Optional properties:
|
|
- label: String to describe controller.
|
|
- qcom,platform-te-gpio: Specifies the gpio used for TE.
|
|
- qcom,panel-te-source: Specifies the source pin for Vsync from panel or WD Timer.
|
|
- qcom,dsi-display-active: Current active display
|
|
- qcom,dsi-ctrl: handle to dsi controller device
|
|
- qcom,dsi-phy: handle to dsi phy device
|
|
- qcom,dsi-ctrl-num: Specifies the DSI controllers to use
|
|
- qcom,dsi-phy-num: Specifies the DSI PHYs to use
|
|
- qcom,dsi-select-clocks: Specifies the required clocks to use
|
|
- qcom,dsi-display-list: Specifies the list of supported displays.
|
|
- qcom,dsi-manager: Specifies dsi manager is present
|
|
- qcom,dsi-display: Specifies dsi display is present
|
|
- qcom,hdmi-display: Specifies hdmi is present
|
|
- qcom,dp-display: Specified dp is present
|
|
- qcom,<type>-supply-entries: A node that lists the elements of the supply used by the
|
|
a particular "type" of DSI module. The module "types"
|
|
can be "core", "ctrl", and "phy". Within the same type,
|
|
there can be more than one instance of this binding,
|
|
in which case the entry would be appended with the
|
|
supply entry index.
|
|
e.g. qcom,ctrl-supply-entry@0
|
|
-- qcom,supply-name: name of the supply (vdd/vdda/vddio)
|
|
-- qcom,supply-min-voltage: minimum voltage level (uV)
|
|
-- qcom,supply-max-voltage: maximum voltage level (uV)
|
|
-- qcom,supply-enable-load: load drawn (uA) from enabled supply
|
|
-- qcom,supply-disable-load: load drawn (uA) from disabled supply
|
|
-- qcom,supply-off-min-voltage: minimum voltage level (uV) when turned off
|
|
-- qcom,supply-pre-on-sleep: time to sleep (ms) before turning on
|
|
-- qcom,supply-post-on-sleep: time to sleep (ms) after turning on
|
|
-- qcom,supply-pre-off-sleep: time to sleep (ms) before turning off
|
|
-- qcom,supply-post-off-sleep: time to sleep (ms) after turning off
|
|
- qcom,mdss-mdp-transfer-time-us: Specifies the dsi transfer time for command mode
|
|
panels in microseconds. Driver uses this number to adjust
|
|
the clock rate according to the expected transfer time.
|
|
Increasing this value would slow down the mdp processing
|
|
and can result in slower performance.
|
|
Decreasing this value can speed up the mdp processing,
|
|
but this can also impact power consumption.
|
|
As a rule this time should not be higher than the time
|
|
that would be expected with the processing at the
|
|
dsi link rate since anyways this would be the maximum
|
|
transfer time that could be achieved.
|
|
If ping pong split enabled, this time should not be higher
|
|
than two times the dsi link rate time.
|
|
If the property is not specified, then the default value is 14000 us.
|
|
- qcom,dsi-phy-isolation-enabled: A boolean property enables the phy isolation from dsi
|
|
controller. This must be enabled for debugging purpose
|
|
only with simulator panel. It should not be enabled for
|
|
normal DSI panels.
|
|
- - qcom,null-insertion-enabled: A boolean to enable NULL packet insertion feature for DSI controller.
|
|
- ports: This video port is used when external bridge is present.
|
|
The connection is modeled using the OF graph bindings
|
|
specified in Documentation/devicetree/bindings/graph.txt.
|
|
Video port 0 reg 0 is for the bridge output. The remote
|
|
endpoint phandle should be mipi_dsi_device device node.
|
|
|