You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
386 lines
11 KiB
386 lines
11 KiB
/*
|
|
* linux/drivers/ide/pci/cs5530.c Version 0.7 Sept 10, 2002
|
|
*
|
|
* Copyright (C) 2000 Andre Hedrick <andre@linux-ide.org>
|
|
* Ditto of GNU General Public License.
|
|
*
|
|
* Copyright (C) 2000 Mark Lord <mlord@pobox.com>
|
|
* May be copied or modified under the terms of the GNU General Public License
|
|
*
|
|
* Development of this chipset driver was funded
|
|
* by the nice folks at National Semiconductor.
|
|
*
|
|
* Documentation:
|
|
* CS5530 documentation available from National Semiconductor.
|
|
*/
|
|
|
|
#include <linux/module.h>
|
|
#include <linux/types.h>
|
|
#include <linux/kernel.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/timer.h>
|
|
#include <linux/mm.h>
|
|
#include <linux/ioport.h>
|
|
#include <linux/blkdev.h>
|
|
#include <linux/hdreg.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/pci.h>
|
|
#include <linux/init.h>
|
|
#include <linux/ide.h>
|
|
#include <asm/io.h>
|
|
#include <asm/irq.h>
|
|
|
|
/**
|
|
* cs5530_xfer_set_mode - set a new transfer mode at the drive
|
|
* @drive: drive to tune
|
|
* @mode: new mode
|
|
*
|
|
* Logging wrapper to the IDE driver speed configuration. This can
|
|
* probably go away now.
|
|
*/
|
|
|
|
static int cs5530_set_xfer_mode (ide_drive_t *drive, u8 mode)
|
|
{
|
|
printk(KERN_DEBUG "%s: cs5530_set_xfer_mode(%s)\n",
|
|
drive->name, ide_xfer_verbose(mode));
|
|
return (ide_config_drive_speed(drive, mode));
|
|
}
|
|
|
|
/*
|
|
* Here are the standard PIO mode 0-4 timings for each "format".
|
|
* Format-0 uses fast data reg timings, with slower command reg timings.
|
|
* Format-1 uses fast timings for all registers, but won't work with all drives.
|
|
*/
|
|
static unsigned int cs5530_pio_timings[2][5] = {
|
|
{0x00009172, 0x00012171, 0x00020080, 0x00032010, 0x00040010},
|
|
{0xd1329172, 0x71212171, 0x30200080, 0x20102010, 0x00100010}
|
|
};
|
|
|
|
/*
|
|
* After chip reset, the PIO timings are set to 0x0000e132, which is not valid.
|
|
*/
|
|
#define CS5530_BAD_PIO(timings) (((timings)&~0x80000000)==0x0000e132)
|
|
#define CS5530_BASEREG(hwif) (((hwif)->dma_base & ~0xf) + ((hwif)->channel ? 0x30 : 0x20))
|
|
|
|
/**
|
|
* cs5530_tuneproc - select/set PIO modes
|
|
*
|
|
* cs5530_tuneproc() handles selection/setting of PIO modes
|
|
* for both the chipset and drive.
|
|
*
|
|
* The ide_init_cs5530() routine guarantees that all drives
|
|
* will have valid default PIO timings set up before we get here.
|
|
*/
|
|
|
|
static void cs5530_tuneproc (ide_drive_t *drive, u8 pio) /* pio=255 means "autotune" */
|
|
{
|
|
ide_hwif_t *hwif = HWIF(drive);
|
|
unsigned int format;
|
|
unsigned long basereg = CS5530_BASEREG(hwif);
|
|
static u8 modes[5] = { XFER_PIO_0, XFER_PIO_1, XFER_PIO_2, XFER_PIO_3, XFER_PIO_4};
|
|
|
|
pio = ide_get_best_pio_mode(drive, pio, 4, NULL);
|
|
if (!cs5530_set_xfer_mode(drive, modes[pio])) {
|
|
format = (hwif->INL(basereg+4) >> 31) & 1;
|
|
hwif->OUTL(cs5530_pio_timings[format][pio],
|
|
basereg+(drive->select.b.unit<<3));
|
|
}
|
|
}
|
|
|
|
/**
|
|
* cs5530_config_dma - select/set DMA and UDMA modes
|
|
* @drive: drive to tune
|
|
*
|
|
* cs5530_config_dma() handles selection/setting of DMA/UDMA modes
|
|
* for both the chipset and drive. The CS5530 has limitations about
|
|
* mixing DMA/UDMA on the same cable.
|
|
*/
|
|
|
|
static int cs5530_config_dma (ide_drive_t *drive)
|
|
{
|
|
int udma_ok = 1, mode = 0;
|
|
ide_hwif_t *hwif = HWIF(drive);
|
|
int unit = drive->select.b.unit;
|
|
ide_drive_t *mate = &hwif->drives[unit^1];
|
|
struct hd_driveid *id = drive->id;
|
|
unsigned int reg, timings;
|
|
unsigned long basereg;
|
|
|
|
/*
|
|
* Default to DMA-off in case we run into trouble here.
|
|
*/
|
|
hwif->ide_dma_off_quietly(drive);
|
|
/* turn off DMA while we fiddle */
|
|
hwif->ide_dma_host_off(drive);
|
|
/* clear DMA_capable bit */
|
|
|
|
/*
|
|
* The CS5530 specifies that two drives sharing a cable cannot
|
|
* mix UDMA/MDMA. It has to be one or the other, for the pair,
|
|
* though different timings can still be chosen for each drive.
|
|
* We could set the appropriate timing bits on the fly,
|
|
* but that might be a bit confusing. So, for now we statically
|
|
* handle this requirement by looking at our mate drive to see
|
|
* what it is capable of, before choosing a mode for our own drive.
|
|
*
|
|
* Note: This relies on the fact we never fail from UDMA to MWDMA_2
|
|
* but instead drop to PIO
|
|
*/
|
|
if (mate->present) {
|
|
struct hd_driveid *mateid = mate->id;
|
|
if (mateid && (mateid->capability & 1) &&
|
|
!__ide_dma_bad_drive(mate)) {
|
|
if ((mateid->field_valid & 4) &&
|
|
(mateid->dma_ultra & 7))
|
|
udma_ok = 1;
|
|
else if ((mateid->field_valid & 2) &&
|
|
(mateid->dma_mword & 7))
|
|
udma_ok = 0;
|
|
else
|
|
udma_ok = 1;
|
|
}
|
|
}
|
|
|
|
/*
|
|
* Now see what the current drive is capable of,
|
|
* selecting UDMA only if the mate said it was ok.
|
|
*/
|
|
if (id && (id->capability & 1) && drive->autodma &&
|
|
!__ide_dma_bad_drive(drive)) {
|
|
if (udma_ok && (id->field_valid & 4) && (id->dma_ultra & 7)) {
|
|
if (id->dma_ultra & 4)
|
|
mode = XFER_UDMA_2;
|
|
else if (id->dma_ultra & 2)
|
|
mode = XFER_UDMA_1;
|
|
else if (id->dma_ultra & 1)
|
|
mode = XFER_UDMA_0;
|
|
}
|
|
if (!mode && (id->field_valid & 2) && (id->dma_mword & 7)) {
|
|
if (id->dma_mword & 4)
|
|
mode = XFER_MW_DMA_2;
|
|
else if (id->dma_mword & 2)
|
|
mode = XFER_MW_DMA_1;
|
|
else if (id->dma_mword & 1)
|
|
mode = XFER_MW_DMA_0;
|
|
}
|
|
}
|
|
|
|
/*
|
|
* Tell the drive to switch to the new mode; abort on failure.
|
|
*/
|
|
if (!mode || cs5530_set_xfer_mode(drive, mode))
|
|
return 1; /* failure */
|
|
|
|
/*
|
|
* Now tune the chipset to match the drive:
|
|
*/
|
|
switch (mode) {
|
|
case XFER_UDMA_0: timings = 0x00921250; break;
|
|
case XFER_UDMA_1: timings = 0x00911140; break;
|
|
case XFER_UDMA_2: timings = 0x00911030; break;
|
|
case XFER_MW_DMA_0: timings = 0x00077771; break;
|
|
case XFER_MW_DMA_1: timings = 0x00012121; break;
|
|
case XFER_MW_DMA_2: timings = 0x00002020; break;
|
|
default:
|
|
printk(KERN_ERR "%s: cs5530_config_dma: huh? mode=%02x\n",
|
|
drive->name, mode);
|
|
return 1; /* failure */
|
|
}
|
|
basereg = CS5530_BASEREG(hwif);
|
|
reg = hwif->INL(basereg+4); /* get drive0 config register */
|
|
timings |= reg & 0x80000000; /* preserve PIO format bit */
|
|
if (unit == 0) { /* are we configuring drive0? */
|
|
hwif->OUTL(timings, basereg+4); /* write drive0 config register */
|
|
} else {
|
|
if (timings & 0x00100000)
|
|
reg |= 0x00100000; /* enable UDMA timings for both drives */
|
|
else
|
|
reg &= ~0x00100000; /* disable UDMA timings for both drives */
|
|
hwif->OUTL(reg, basereg+4); /* write drive0 config register */
|
|
hwif->OUTL(timings, basereg+12); /* write drive1 config register */
|
|
}
|
|
(void) hwif->ide_dma_host_on(drive);
|
|
/* set DMA_capable bit */
|
|
|
|
/*
|
|
* Finally, turn DMA on in software, and exit.
|
|
*/
|
|
return hwif->ide_dma_on(drive); /* success */
|
|
}
|
|
|
|
/**
|
|
* init_chipset_5530 - set up 5530 bridge
|
|
* @dev: PCI device
|
|
* @name: device name
|
|
*
|
|
* Initialize the cs5530 bridge for reliable IDE DMA operation.
|
|
*/
|
|
|
|
static unsigned int __devinit init_chipset_cs5530 (struct pci_dev *dev, const char *name)
|
|
{
|
|
struct pci_dev *master_0 = NULL, *cs5530_0 = NULL;
|
|
unsigned long flags;
|
|
|
|
dev = NULL;
|
|
while ((dev = pci_get_device(PCI_VENDOR_ID_CYRIX, PCI_ANY_ID, dev)) != NULL) {
|
|
switch (dev->device) {
|
|
case PCI_DEVICE_ID_CYRIX_PCI_MASTER:
|
|
master_0 = pci_dev_get(dev);
|
|
break;
|
|
case PCI_DEVICE_ID_CYRIX_5530_LEGACY:
|
|
cs5530_0 = pci_dev_get(dev);
|
|
break;
|
|
}
|
|
}
|
|
if (!master_0) {
|
|
printk(KERN_ERR "%s: unable to locate PCI MASTER function\n", name);
|
|
goto out;
|
|
}
|
|
if (!cs5530_0) {
|
|
printk(KERN_ERR "%s: unable to locate CS5530 LEGACY function\n", name);
|
|
goto out;
|
|
}
|
|
|
|
spin_lock_irqsave(&ide_lock, flags);
|
|
/* all CPUs (there should only be one CPU with this chipset) */
|
|
|
|
/*
|
|
* Enable BusMaster and MemoryWriteAndInvalidate for the cs5530:
|
|
* --> OR 0x14 into 16-bit PCI COMMAND reg of function 0 of the cs5530
|
|
*/
|
|
|
|
pci_set_master(cs5530_0);
|
|
pci_set_mwi(cs5530_0);
|
|
|
|
/*
|
|
* Set PCI CacheLineSize to 16-bytes:
|
|
* --> Write 0x04 into 8-bit PCI CACHELINESIZE reg of function 0 of the cs5530
|
|
*/
|
|
|
|
pci_write_config_byte(cs5530_0, PCI_CACHE_LINE_SIZE, 0x04);
|
|
|
|
/*
|
|
* Disable trapping of UDMA register accesses (Win98 hack):
|
|
* --> Write 0x5006 into 16-bit reg at offset 0xd0 of function 0 of the cs5530
|
|
*/
|
|
|
|
pci_write_config_word(cs5530_0, 0xd0, 0x5006);
|
|
|
|
/*
|
|
* Bit-1 at 0x40 enables MemoryWriteAndInvalidate on internal X-bus:
|
|
* The other settings are what is necessary to get the register
|
|
* into a sane state for IDE DMA operation.
|
|
*/
|
|
|
|
pci_write_config_byte(master_0, 0x40, 0x1e);
|
|
|
|
/*
|
|
* Set max PCI burst size (16-bytes seems to work best):
|
|
* 16bytes: set bit-1 at 0x41 (reg value of 0x16)
|
|
* all others: clear bit-1 at 0x41, and do:
|
|
* 128bytes: OR 0x00 at 0x41
|
|
* 256bytes: OR 0x04 at 0x41
|
|
* 512bytes: OR 0x08 at 0x41
|
|
* 1024bytes: OR 0x0c at 0x41
|
|
*/
|
|
|
|
pci_write_config_byte(master_0, 0x41, 0x14);
|
|
|
|
/*
|
|
* These settings are necessary to get the chip
|
|
* into a sane state for IDE DMA operation.
|
|
*/
|
|
|
|
pci_write_config_byte(master_0, 0x42, 0x00);
|
|
pci_write_config_byte(master_0, 0x43, 0xc1);
|
|
|
|
spin_unlock_irqrestore(&ide_lock, flags);
|
|
|
|
out:
|
|
pci_dev_put(master_0);
|
|
pci_dev_put(cs5530_0);
|
|
return 0;
|
|
}
|
|
|
|
/**
|
|
* init_hwif_cs5530 - initialise an IDE channel
|
|
* @hwif: IDE to initialize
|
|
*
|
|
* This gets invoked by the IDE driver once for each channel. It
|
|
* performs channel-specific pre-initialization before drive probing.
|
|
*/
|
|
|
|
static void __devinit init_hwif_cs5530 (ide_hwif_t *hwif)
|
|
{
|
|
unsigned long basereg;
|
|
u32 d0_timings;
|
|
hwif->autodma = 0;
|
|
|
|
if (hwif->mate)
|
|
hwif->serialized = hwif->mate->serialized = 1;
|
|
|
|
hwif->tuneproc = &cs5530_tuneproc;
|
|
basereg = CS5530_BASEREG(hwif);
|
|
d0_timings = hwif->INL(basereg+0);
|
|
if (CS5530_BAD_PIO(d0_timings)) {
|
|
/* PIO timings not initialized? */
|
|
hwif->OUTL(cs5530_pio_timings[(d0_timings>>31)&1][0], basereg+0);
|
|
if (!hwif->drives[0].autotune)
|
|
hwif->drives[0].autotune = 1;
|
|
/* needs autotuning later */
|
|
}
|
|
if (CS5530_BAD_PIO(hwif->INL(basereg+8))) {
|
|
/* PIO timings not initialized? */
|
|
hwif->OUTL(cs5530_pio_timings[(d0_timings>>31)&1][0], basereg+8);
|
|
if (!hwif->drives[1].autotune)
|
|
hwif->drives[1].autotune = 1;
|
|
/* needs autotuning later */
|
|
}
|
|
|
|
hwif->atapi_dma = 1;
|
|
hwif->ultra_mask = 0x07;
|
|
hwif->mwdma_mask = 0x07;
|
|
|
|
hwif->ide_dma_check = &cs5530_config_dma;
|
|
if (!noautodma)
|
|
hwif->autodma = 1;
|
|
hwif->drives[0].autodma = hwif->autodma;
|
|
hwif->drives[1].autodma = hwif->autodma;
|
|
}
|
|
|
|
static ide_pci_device_t cs5530_chipset __devinitdata = {
|
|
.name = "CS5530",
|
|
.init_chipset = init_chipset_cs5530,
|
|
.init_hwif = init_hwif_cs5530,
|
|
.channels = 2,
|
|
.autodma = AUTODMA,
|
|
.bootable = ON_BOARD,
|
|
};
|
|
|
|
static int __devinit cs5530_init_one(struct pci_dev *dev, const struct pci_device_id *id)
|
|
{
|
|
return ide_setup_pci_device(dev, &cs5530_chipset);
|
|
}
|
|
|
|
static struct pci_device_id cs5530_pci_tbl[] = {
|
|
{ PCI_VENDOR_ID_CYRIX, PCI_DEVICE_ID_CYRIX_5530_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
|
|
{ 0, },
|
|
};
|
|
MODULE_DEVICE_TABLE(pci, cs5530_pci_tbl);
|
|
|
|
static struct pci_driver driver = {
|
|
.name = "CS5530 IDE",
|
|
.id_table = cs5530_pci_tbl,
|
|
.probe = cs5530_init_one,
|
|
};
|
|
|
|
static int cs5530_ide_init(void)
|
|
{
|
|
return ide_pci_register_driver(&driver);
|
|
}
|
|
|
|
module_init(cs5530_ide_init);
|
|
|
|
MODULE_AUTHOR("Mark Lord");
|
|
MODULE_DESCRIPTION("PCI driver module for Cyrix/NS 5530 IDE");
|
|
MODULE_LICENSE("GPL");
|
|
|