You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
556 lines
20 KiB
556 lines
20 KiB
/*
|
|
* This file is part of wl12xx
|
|
*
|
|
* Copyright (C) 1998-2009 Texas Instruments. All rights reserved.
|
|
* Copyright (C) 2009 Nokia Corporation
|
|
*
|
|
* Contact: Luciano Coelho <luciano.coelho@nokia.com>
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License
|
|
* version 2 as published by the Free Software Foundation.
|
|
*
|
|
* This program is distributed in the hope that it will be useful, but
|
|
* WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
|
|
* General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program; if not, write to the Free Software
|
|
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
|
|
* 02110-1301 USA
|
|
*
|
|
*/
|
|
|
|
#ifndef __REG_H__
|
|
#define __REG_H__
|
|
|
|
#include <linux/bitops.h>
|
|
|
|
#define REGISTERS_BASE 0x00300000
|
|
#define DRPW_BASE 0x00310000
|
|
|
|
#define REGISTERS_DOWN_SIZE 0x00008800
|
|
#define REGISTERS_WORK_SIZE 0x0000b000
|
|
|
|
#define FW_STATUS_ADDR (0x14FC0 + 0xA000)
|
|
|
|
/*===============================================
|
|
Host Software Reset - 32bit RW
|
|
------------------------------------------
|
|
[31:1] Reserved
|
|
0 SOFT_RESET Soft Reset - When this bit is set,
|
|
it holds the Wlan hardware in a soft reset state.
|
|
This reset disables all MAC and baseband processor
|
|
clocks except the CardBus/PCI interface clock.
|
|
It also initializes all MAC state machines except
|
|
the host interface. It does not reload the
|
|
contents of the EEPROM. When this bit is cleared
|
|
(not self-clearing), the Wlan hardware
|
|
exits the software reset state.
|
|
===============================================*/
|
|
#define WL12XX_SLV_SOFT_RESET (REGISTERS_BASE + 0x0000)
|
|
|
|
#define WL1271_SLV_REG_DATA (REGISTERS_BASE + 0x0008)
|
|
#define WL1271_SLV_REG_ADATA (REGISTERS_BASE + 0x000c)
|
|
#define WL1271_SLV_MEM_DATA (REGISTERS_BASE + 0x0018)
|
|
|
|
#define WL12XX_REG_INTERRUPT_TRIG (REGISTERS_BASE + 0x0474)
|
|
#define WL12XX_REG_INTERRUPT_TRIG_H (REGISTERS_BASE + 0x0478)
|
|
|
|
/*=============================================
|
|
Host Interrupt Mask Register - 32bit (RW)
|
|
------------------------------------------
|
|
Setting a bit in this register masks the
|
|
corresponding interrupt to the host.
|
|
0 - RX0 - Rx first dubble buffer Data Interrupt
|
|
1 - TXD - Tx Data Interrupt
|
|
2 - TXXFR - Tx Transfer Interrupt
|
|
3 - RX1 - Rx second dubble buffer Data Interrupt
|
|
4 - RXXFR - Rx Transfer Interrupt
|
|
5 - EVENT_A - Event Mailbox interrupt
|
|
6 - EVENT_B - Event Mailbox interrupt
|
|
7 - WNONHST - Wake On Host Interrupt
|
|
8 - TRACE_A - Debug Trace interrupt
|
|
9 - TRACE_B - Debug Trace interrupt
|
|
10 - CDCMP - Command Complete Interrupt
|
|
11 -
|
|
12 -
|
|
13 -
|
|
14 - ICOMP - Initialization Complete Interrupt
|
|
16 - SG SE - Soft Gemini - Sense enable interrupt
|
|
17 - SG SD - Soft Gemini - Sense disable interrupt
|
|
18 - -
|
|
19 - -
|
|
20 - -
|
|
21- -
|
|
Default: 0x0001
|
|
*==============================================*/
|
|
#define WL12XX_REG_INTERRUPT_MASK (REGISTERS_BASE + 0x04DC)
|
|
|
|
/*=============================================
|
|
Host Interrupt Mask Set 16bit, (Write only)
|
|
------------------------------------------
|
|
Setting a bit in this register sets
|
|
the corresponding bin in ACX_HINT_MASK register
|
|
without effecting the mask
|
|
state of other bits (0 = no effect).
|
|
==============================================*/
|
|
#define ACX_REG_HINT_MASK_SET (REGISTERS_BASE + 0x04E0)
|
|
|
|
/*=============================================
|
|
Host Interrupt Mask Clear 16bit,(Write only)
|
|
------------------------------------------
|
|
Setting a bit in this register clears
|
|
the corresponding bin in ACX_HINT_MASK register
|
|
without effecting the mask
|
|
state of other bits (0 = no effect).
|
|
=============================================*/
|
|
#define ACX_REG_HINT_MASK_CLR (REGISTERS_BASE + 0x04E4)
|
|
|
|
/*=============================================
|
|
Host Interrupt Status Nondestructive Read
|
|
16bit,(Read only)
|
|
------------------------------------------
|
|
The host can read this register to determine
|
|
which interrupts are active.
|
|
Reading this register doesn't
|
|
effect its content.
|
|
=============================================*/
|
|
#define WL12XX_REG_INTERRUPT_NO_CLEAR (REGISTERS_BASE + 0x04E8)
|
|
|
|
/*=============================================
|
|
Host Interrupt Status Clear on Read Register
|
|
16bit,(Read only)
|
|
------------------------------------------
|
|
The host can read this register to determine
|
|
which interrupts are active.
|
|
Reading this register clears it,
|
|
thus making all interrupts inactive.
|
|
==============================================*/
|
|
#define ACX_REG_INTERRUPT_CLEAR (REGISTERS_BASE + 0x04F8)
|
|
|
|
/*=============================================
|
|
Host Interrupt Acknowledge Register
|
|
16bit,(Write only)
|
|
------------------------------------------
|
|
The host can set individual bits in this
|
|
register to clear (acknowledge) the corresp.
|
|
interrupt status bits in the HINT_STS_CLR and
|
|
HINT_STS_ND registers, thus making the
|
|
assotiated interrupt inactive. (0-no effect)
|
|
==============================================*/
|
|
#define WL12XX_REG_INTERRUPT_ACK (REGISTERS_BASE + 0x04F0)
|
|
|
|
#define WL12XX_REG_RX_DRIVER_COUNTER (REGISTERS_BASE + 0x0538)
|
|
|
|
/* Device Configuration registers*/
|
|
#define SOR_CFG (REGISTERS_BASE + 0x0800)
|
|
|
|
/* Embedded ARM CPU Control */
|
|
|
|
/*===============================================
|
|
Halt eCPU - 32bit RW
|
|
------------------------------------------
|
|
0 HALT_ECPU Halt Embedded CPU - This bit is the
|
|
compliment of bit 1 (MDATA2) in the SOR_CFG register.
|
|
During a hardware reset, this bit holds
|
|
the inverse of MDATA2.
|
|
When downloading firmware from the host,
|
|
set this bit (pull down MDATA2).
|
|
The host clears this bit after downloading the firmware into
|
|
zero-wait-state SSRAM.
|
|
When loading firmware from Flash, clear this bit (pull up MDATA2)
|
|
so that the eCPU can run the bootloader code in Flash
|
|
HALT_ECPU eCPU State
|
|
--------------------
|
|
1 halt eCPU
|
|
0 enable eCPU
|
|
===============================================*/
|
|
#define WL12XX_REG_ECPU_CONTROL (REGISTERS_BASE + 0x0804)
|
|
|
|
#define WL12XX_HI_CFG (REGISTERS_BASE + 0x0808)
|
|
|
|
/*===============================================
|
|
EEPROM Burst Read Start - 32bit RW
|
|
------------------------------------------
|
|
[31:1] Reserved
|
|
0 ACX_EE_START - EEPROM Burst Read Start 0
|
|
Setting this bit starts a burst read from
|
|
the external EEPROM.
|
|
If this bit is set (after reset) before an EEPROM read/write,
|
|
the burst read starts at EEPROM address 0.
|
|
Otherwise, it starts at the address
|
|
following the address of the previous access.
|
|
TheWlan hardware hardware clears this bit automatically.
|
|
|
|
Default: 0x00000000
|
|
*================================================*/
|
|
#define ACX_REG_EE_START (REGISTERS_BASE + 0x080C)
|
|
|
|
#define WL12XX_OCP_POR_CTR (REGISTERS_BASE + 0x09B4)
|
|
#define WL12XX_OCP_DATA_WRITE (REGISTERS_BASE + 0x09B8)
|
|
#define WL12XX_OCP_DATA_READ (REGISTERS_BASE + 0x09BC)
|
|
#define WL12XX_OCP_CMD (REGISTERS_BASE + 0x09C0)
|
|
|
|
#define WL12XX_HOST_WR_ACCESS (REGISTERS_BASE + 0x09F8)
|
|
|
|
#define WL12XX_CHIP_ID_B (REGISTERS_BASE + 0x5674)
|
|
|
|
#define WL12XX_ENABLE (REGISTERS_BASE + 0x5450)
|
|
|
|
/* Power Management registers */
|
|
#define WL12XX_ELP_CFG_MODE (REGISTERS_BASE + 0x5804)
|
|
#define WL12XX_ELP_CMD (REGISTERS_BASE + 0x5808)
|
|
#define WL12XX_PLL_CAL_TIME (REGISTERS_BASE + 0x5810)
|
|
#define WL12XX_CLK_REQ_TIME (REGISTERS_BASE + 0x5814)
|
|
#define WL12XX_CLK_BUF_TIME (REGISTERS_BASE + 0x5818)
|
|
|
|
#define WL12XX_CFG_PLL_SYNC_CNT (REGISTERS_BASE + 0x5820)
|
|
|
|
/* Scratch Pad registers*/
|
|
#define WL12XX_SCR_PAD0 (REGISTERS_BASE + 0x5608)
|
|
#define WL12XX_SCR_PAD1 (REGISTERS_BASE + 0x560C)
|
|
#define WL12XX_SCR_PAD2 (REGISTERS_BASE + 0x5610)
|
|
#define WL12XX_SCR_PAD3 (REGISTERS_BASE + 0x5614)
|
|
#define WL12XX_SCR_PAD4 (REGISTERS_BASE + 0x5618)
|
|
#define WL12XX_SCR_PAD4_SET (REGISTERS_BASE + 0x561C)
|
|
#define WL12XX_SCR_PAD4_CLR (REGISTERS_BASE + 0x5620)
|
|
#define WL12XX_SCR_PAD5 (REGISTERS_BASE + 0x5624)
|
|
#define WL12XX_SCR_PAD5_SET (REGISTERS_BASE + 0x5628)
|
|
#define WL12XX_SCR_PAD5_CLR (REGISTERS_BASE + 0x562C)
|
|
#define WL12XX_SCR_PAD6 (REGISTERS_BASE + 0x5630)
|
|
#define WL12XX_SCR_PAD7 (REGISTERS_BASE + 0x5634)
|
|
#define WL12XX_SCR_PAD8 (REGISTERS_BASE + 0x5638)
|
|
#define WL12XX_SCR_PAD9 (REGISTERS_BASE + 0x563C)
|
|
|
|
/* Spare registers*/
|
|
#define WL12XX_SPARE_A1 (REGISTERS_BASE + 0x0994)
|
|
#define WL12XX_SPARE_A2 (REGISTERS_BASE + 0x0998)
|
|
#define WL12XX_SPARE_A3 (REGISTERS_BASE + 0x099C)
|
|
#define WL12XX_SPARE_A4 (REGISTERS_BASE + 0x09A0)
|
|
#define WL12XX_SPARE_A5 (REGISTERS_BASE + 0x09A4)
|
|
#define WL12XX_SPARE_A6 (REGISTERS_BASE + 0x09A8)
|
|
#define WL12XX_SPARE_A7 (REGISTERS_BASE + 0x09AC)
|
|
#define WL12XX_SPARE_A8 (REGISTERS_BASE + 0x09B0)
|
|
#define WL12XX_SPARE_B1 (REGISTERS_BASE + 0x5420)
|
|
#define WL12XX_SPARE_B2 (REGISTERS_BASE + 0x5424)
|
|
#define WL12XX_SPARE_B3 (REGISTERS_BASE + 0x5428)
|
|
#define WL12XX_SPARE_B4 (REGISTERS_BASE + 0x542C)
|
|
#define WL12XX_SPARE_B5 (REGISTERS_BASE + 0x5430)
|
|
#define WL12XX_SPARE_B6 (REGISTERS_BASE + 0x5434)
|
|
#define WL12XX_SPARE_B7 (REGISTERS_BASE + 0x5438)
|
|
#define WL12XX_SPARE_B8 (REGISTERS_BASE + 0x543C)
|
|
|
|
#define WL12XX_PLL_PARAMETERS (REGISTERS_BASE + 0x6040)
|
|
#define WL12XX_WU_COUNTER_PAUSE (REGISTERS_BASE + 0x6008)
|
|
#define WL12XX_WELP_ARM_COMMAND (REGISTERS_BASE + 0x6100)
|
|
#define WL12XX_DRPW_SCRATCH_START (DRPW_BASE + 0x002C)
|
|
|
|
#define WL12XX_CMD_MBOX_ADDRESS 0x407B4
|
|
|
|
#define ACX_REG_EEPROM_START_BIT BIT(1)
|
|
|
|
/* Command/Information Mailbox Pointers */
|
|
|
|
/*===============================================
|
|
Command Mailbox Pointer - 32bit RW
|
|
------------------------------------------
|
|
This register holds the start address of
|
|
the command mailbox located in the Wlan hardware memory.
|
|
The host must read this pointer after a reset to
|
|
find the location of the command mailbox.
|
|
The Wlan hardware initializes the command mailbox
|
|
pointer with the default address of the command mailbox.
|
|
The command mailbox pointer is not valid until after
|
|
the host receives the Init Complete interrupt from
|
|
the Wlan hardware.
|
|
===============================================*/
|
|
#define WL12XX_REG_COMMAND_MAILBOX_PTR (WL12XX_SCR_PAD0)
|
|
|
|
/*===============================================
|
|
Information Mailbox Pointer - 32bit RW
|
|
------------------------------------------
|
|
This register holds the start address of
|
|
the information mailbox located in the Wlan hardware memory.
|
|
The host must read this pointer after a reset to find
|
|
the location of the information mailbox.
|
|
The Wlan hardware initializes the information mailbox pointer
|
|
with the default address of the information mailbox.
|
|
The information mailbox pointer is not valid
|
|
until after the host receives the Init Complete interrupt from
|
|
the Wlan hardware.
|
|
===============================================*/
|
|
#define WL12XX_REG_EVENT_MAILBOX_PTR (WL12XX_SCR_PAD1)
|
|
|
|
/*===============================================
|
|
EEPROM Read/Write Request 32bit RW
|
|
------------------------------------------
|
|
1 EE_READ - EEPROM Read Request 1 - Setting this bit
|
|
loads a single byte of data into the EE_DATA
|
|
register from the EEPROM location specified in
|
|
the EE_ADDR register.
|
|
The Wlan hardware hardware clears this bit automatically.
|
|
EE_DATA is valid when this bit is cleared.
|
|
|
|
0 EE_WRITE - EEPROM Write Request - Setting this bit
|
|
writes a single byte of data from the EE_DATA register into the
|
|
EEPROM location specified in the EE_ADDR register.
|
|
The Wlan hardware hardware clears this bit automatically.
|
|
*===============================================*/
|
|
#define ACX_EE_CTL_REG EE_CTL
|
|
#define EE_WRITE 0x00000001ul
|
|
#define EE_READ 0x00000002ul
|
|
|
|
/*===============================================
|
|
EEPROM Address - 32bit RW
|
|
------------------------------------------
|
|
This register specifies the address
|
|
within the EEPROM from/to which to read/write data.
|
|
===============================================*/
|
|
#define ACX_EE_ADDR_REG EE_ADDR
|
|
|
|
/*===============================================
|
|
EEPROM Data - 32bit RW
|
|
------------------------------------------
|
|
This register either holds the read 8 bits of
|
|
data from the EEPROM or the write data
|
|
to be written to the EEPROM.
|
|
===============================================*/
|
|
#define ACX_EE_DATA_REG EE_DATA
|
|
|
|
/*===============================================
|
|
EEPROM Base Address - 32bit RW
|
|
------------------------------------------
|
|
This register holds the upper nine bits
|
|
[23:15] of the 24-bit Wlan hardware memory
|
|
address for burst reads from EEPROM accesses.
|
|
The EEPROM provides the lower 15 bits of this address.
|
|
The MSB of the address from the EEPROM is ignored.
|
|
===============================================*/
|
|
#define ACX_EE_CFG EE_CFG
|
|
|
|
/*===============================================
|
|
GPIO Output Values -32bit, RW
|
|
------------------------------------------
|
|
[31:16] Reserved
|
|
[15: 0] Specify the output values (at the output driver inputs) for
|
|
GPIO[15:0], respectively.
|
|
===============================================*/
|
|
#define ACX_GPIO_OUT_REG GPIO_OUT
|
|
#define ACX_MAX_GPIO_LINES 15
|
|
|
|
/*===============================================
|
|
Contention window -32bit, RW
|
|
------------------------------------------
|
|
[31:26] Reserved
|
|
[25:16] Max (0x3ff)
|
|
[15:07] Reserved
|
|
[06:00] Current contention window value - default is 0x1F
|
|
===============================================*/
|
|
#define ACX_CONT_WIND_CFG_REG CONT_WIND_CFG
|
|
#define ACX_CONT_WIND_MIN_MASK 0x0000007f
|
|
#define ACX_CONT_WIND_MAX 0x03ff0000
|
|
|
|
#define REF_FREQ_19_2 0
|
|
#define REF_FREQ_26_0 1
|
|
#define REF_FREQ_38_4 2
|
|
#define REF_FREQ_40_0 3
|
|
#define REF_FREQ_33_6 4
|
|
#define REF_FREQ_NUM 5
|
|
|
|
#define LUT_PARAM_INTEGER_DIVIDER 0
|
|
#define LUT_PARAM_FRACTIONAL_DIVIDER 1
|
|
#define LUT_PARAM_ATTN_BB 2
|
|
#define LUT_PARAM_ALPHA_BB 3
|
|
#define LUT_PARAM_STOP_TIME_BB 4
|
|
#define LUT_PARAM_BB_PLL_LOOP_FILTER 5
|
|
#define LUT_PARAM_NUM 6
|
|
|
|
#define WL12XX_EEPROMLESS_IND (WL12XX_SCR_PAD4)
|
|
#define USE_EEPROM 0
|
|
#define NVS_DATA_BUNDARY_ALIGNMENT 4
|
|
|
|
/* Firmware image header size */
|
|
#define FW_HDR_SIZE 8
|
|
|
|
/******************************************************************************
|
|
|
|
CHANNELS, BAND & REG DOMAINS definitions
|
|
|
|
******************************************************************************/
|
|
|
|
#define SHORT_PREAMBLE_BIT BIT(0) /* CCK or Barker depending on the rate */
|
|
#define OFDM_RATE_BIT BIT(6)
|
|
#define PBCC_RATE_BIT BIT(7)
|
|
|
|
enum {
|
|
CCK_LONG = 0,
|
|
CCK_SHORT = SHORT_PREAMBLE_BIT,
|
|
PBCC_LONG = PBCC_RATE_BIT,
|
|
PBCC_SHORT = PBCC_RATE_BIT | SHORT_PREAMBLE_BIT,
|
|
OFDM = OFDM_RATE_BIT
|
|
};
|
|
|
|
/******************************************************************************
|
|
|
|
Transmit-Descriptor RATE-SET field definitions...
|
|
|
|
Define a new "Rate-Set" for TX path that incorporates the
|
|
Rate & Modulation info into a single 16-bit field.
|
|
|
|
TxdRateSet_t:
|
|
b15 - Indicates Preamble type (1=SHORT, 0=LONG).
|
|
Notes:
|
|
Must be LONG (0) for 1Mbps rate.
|
|
Does not apply (set to 0) for RevG-OFDM rates.
|
|
b14 - Indicates PBCC encoding (1=PBCC, 0=not).
|
|
Notes:
|
|
Does not apply (set to 0) for rates 1 and 2 Mbps.
|
|
Does not apply (set to 0) for RevG-OFDM rates.
|
|
b13 - Unused (set to 0).
|
|
b12-b0 - Supported Rate indicator bits as defined below.
|
|
|
|
******************************************************************************/
|
|
|
|
#define OCP_CMD_LOOP 32
|
|
#define OCP_CMD_WRITE 0x1
|
|
#define OCP_CMD_READ 0x2
|
|
#define OCP_READY_MASK BIT(18)
|
|
#define OCP_STATUS_MASK (BIT(16) | BIT(17))
|
|
#define OCP_STATUS_NO_RESP 0x00000
|
|
#define OCP_STATUS_OK 0x10000
|
|
#define OCP_STATUS_REQ_FAILED 0x20000
|
|
#define OCP_STATUS_RESP_ERROR 0x30000
|
|
|
|
#define OCP_REG_POLARITY 0x0064
|
|
#define OCP_REG_CLK_TYPE 0x0448
|
|
#define OCP_REG_CLK_POLARITY 0x0cb2
|
|
#define OCP_REG_CLK_PULL 0x0cb4
|
|
|
|
#define POLARITY_LOW BIT(1)
|
|
#define NO_PULL (BIT(14) | BIT(15))
|
|
|
|
#define FREF_CLK_TYPE_BITS 0xfffffe7f
|
|
#define CLK_REQ_PRCM 0x100
|
|
#define FREF_CLK_POLARITY_BITS 0xfffff8ff
|
|
#define CLK_REQ_OUTN_SEL 0x700
|
|
|
|
#define WU_COUNTER_PAUSE_VAL 0x3FF
|
|
|
|
/* PLL configuration algorithm for wl128x */
|
|
#define SYS_CLK_CFG_REG 0x2200
|
|
/* Bit[0] - 0-TCXO, 1-FREF */
|
|
#define MCS_PLL_CLK_SEL_FREF BIT(0)
|
|
/* Bit[3:2] - 01-TCXO, 10-FREF */
|
|
#define WL_CLK_REQ_TYPE_FREF BIT(3)
|
|
#define WL_CLK_REQ_TYPE_PG2 (BIT(3) | BIT(2))
|
|
/* Bit[4] - 0-TCXO, 1-FREF */
|
|
#define PRCM_CM_EN_MUX_WLAN_FREF BIT(4)
|
|
|
|
#define TCXO_ILOAD_INT_REG 0x2264
|
|
#define TCXO_CLK_DETECT_REG 0x2266
|
|
|
|
#define TCXO_DET_FAILED BIT(4)
|
|
|
|
#define FREF_ILOAD_INT_REG 0x2084
|
|
#define FREF_CLK_DETECT_REG 0x2086
|
|
#define FREF_CLK_DETECT_FAIL BIT(4)
|
|
|
|
/* Use this reg for masking during driver access */
|
|
#define WL_SPARE_REG 0x2320
|
|
#define WL_SPARE_VAL BIT(2)
|
|
/* Bit[6:5:3] - mask wl write SYS_CLK_CFG[8:5:2:4] */
|
|
#define WL_SPARE_MASK_8526 (BIT(6) | BIT(5) | BIT(3))
|
|
|
|
#define PLL_LOCK_COUNTERS_REG 0xD8C
|
|
#define PLL_LOCK_COUNTERS_COEX 0x0F
|
|
#define PLL_LOCK_COUNTERS_MCS 0xF0
|
|
#define MCS_PLL_OVERRIDE_REG 0xD90
|
|
#define MCS_PLL_CONFIG_REG 0xD92
|
|
#define MCS_SEL_IN_FREQ_MASK 0x0070
|
|
#define MCS_SEL_IN_FREQ_SHIFT 4
|
|
#define MCS_PLL_CONFIG_REG_VAL 0x73
|
|
#define MCS_PLL_ENABLE_HP (BIT(0) | BIT(1))
|
|
|
|
#define MCS_PLL_M_REG 0xD94
|
|
#define MCS_PLL_N_REG 0xD96
|
|
#define MCS_PLL_M_REG_VAL 0xC8
|
|
#define MCS_PLL_N_REG_VAL 0x07
|
|
|
|
#define SDIO_IO_DS 0xd14
|
|
|
|
/* SDIO/wSPI DS configuration values */
|
|
enum {
|
|
HCI_IO_DS_8MA = 0,
|
|
HCI_IO_DS_4MA = 1, /* default */
|
|
HCI_IO_DS_6MA = 2,
|
|
HCI_IO_DS_2MA = 3,
|
|
};
|
|
|
|
/* end PLL configuration algorithm for wl128x */
|
|
|
|
/*
|
|
* Host Command Interrupt. Setting this bit masks
|
|
* the interrupt that the host issues to inform
|
|
* the FW that it has sent a command
|
|
* to the Wlan hardware Command Mailbox.
|
|
*/
|
|
#define WL12XX_INTR_TRIG_CMD BIT(0)
|
|
|
|
/*
|
|
* Host Event Acknowlegde Interrupt. The host
|
|
* sets this bit to acknowledge that it received
|
|
* the unsolicited information from the event
|
|
* mailbox.
|
|
*/
|
|
#define WL12XX_INTR_TRIG_EVENT_ACK BIT(1)
|
|
|
|
/*===============================================
|
|
HI_CFG Interface Configuration Register Values
|
|
------------------------------------------
|
|
===============================================*/
|
|
#define HI_CFG_UART_ENABLE 0x00000004
|
|
#define HI_CFG_RST232_ENABLE 0x00000008
|
|
#define HI_CFG_CLOCK_REQ_SELECT 0x00000010
|
|
#define HI_CFG_HOST_INT_ENABLE 0x00000020
|
|
#define HI_CFG_VLYNQ_OUTPUT_ENABLE 0x00000040
|
|
#define HI_CFG_HOST_INT_ACTIVE_LOW 0x00000080
|
|
#define HI_CFG_UART_TX_OUT_GPIO_15 0x00000100
|
|
#define HI_CFG_UART_TX_OUT_GPIO_14 0x00000200
|
|
#define HI_CFG_UART_TX_OUT_GPIO_7 0x00000400
|
|
|
|
#define HI_CFG_DEF_VAL \
|
|
(HI_CFG_UART_ENABLE | \
|
|
HI_CFG_RST232_ENABLE | \
|
|
HI_CFG_CLOCK_REQ_SELECT | \
|
|
HI_CFG_HOST_INT_ENABLE)
|
|
|
|
#define WL127X_REG_FUSE_DATA_2_1 0x050a
|
|
#define WL128X_REG_FUSE_DATA_2_1 0x2152
|
|
#define PG_VER_MASK 0x3c
|
|
#define PG_VER_OFFSET 2
|
|
|
|
#define WL127X_PG_MAJOR_VER_MASK 0x3
|
|
#define WL127X_PG_MAJOR_VER_OFFSET 0x0
|
|
#define WL127X_PG_MINOR_VER_MASK 0xc
|
|
#define WL127X_PG_MINOR_VER_OFFSET 0x2
|
|
|
|
#define WL128X_PG_MAJOR_VER_MASK 0xc
|
|
#define WL128X_PG_MAJOR_VER_OFFSET 0x2
|
|
#define WL128X_PG_MINOR_VER_MASK 0x3
|
|
#define WL128X_PG_MINOR_VER_OFFSET 0x0
|
|
|
|
#define WL127X_PG_GET_MAJOR(pg_ver) ((pg_ver & WL127X_PG_MAJOR_VER_MASK) >> \
|
|
WL127X_PG_MAJOR_VER_OFFSET)
|
|
#define WL127X_PG_GET_MINOR(pg_ver) ((pg_ver & WL127X_PG_MINOR_VER_MASK) >> \
|
|
WL127X_PG_MINOR_VER_OFFSET)
|
|
#define WL128X_PG_GET_MAJOR(pg_ver) ((pg_ver & WL128X_PG_MAJOR_VER_MASK) >> \
|
|
WL128X_PG_MAJOR_VER_OFFSET)
|
|
#define WL128X_PG_GET_MINOR(pg_ver) ((pg_ver & WL128X_PG_MINOR_VER_MASK) >> \
|
|
WL128X_PG_MINOR_VER_OFFSET)
|
|
|
|
#define WL12XX_REG_FUSE_BD_ADDR_1 0x00310eb4
|
|
#define WL12XX_REG_FUSE_BD_ADDR_2 0x00310eb8
|
|
|
|
#endif
|
|
|