Adds support for policy routing rules including a new
local table for routes with a local destination.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the framework to support multiple IPv6 routing tables.
Currently all automatically generated routes are put into the
same table. This could be changed at a later point after
considering the produced locking overhead.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts IPSec/ESP to use the new block cipher type where
applicable. Similar to the HMAC conversion, existing algorithm names
have been kept for compatibility.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds the structure xfrm_mode. It is meant to represent
the operations carried out by transport/tunnel modes.
By doing this we allow additional encapsulation modes to be added
without clogging up the xfrm_input/xfrm_output paths.
Candidate modes include 4-to-6 tunnel mode, 6-to-4 tunnel mode, and
BEET modes.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Basically this patch moves the generic tunnel protocol stuff out of
xfrm4_tunnel/xfrm6_tunnel and moves it into the new files of tunnel4.c
and tunnel6 respectively.
The reason for this is that the problem that Hugo uncovered is only
the tip of the iceberg. The real problem is that when we removed the
dependency of ipip on xfrm4_tunnel we didn't really consider the module
case at all.
For instance, as it is it's possible to build both ipip and xfrm4_tunnel
as modules and if the latter is loaded then ipip simply won't load.
After considering the alternatives I've decided that the best way out of
this is to restore the dependency of ipip on the non-xfrm-specific part
of xfrm4_tunnel. This is acceptable IMHO because the intention of the
removal was really to be able to use ipip without the xfrm subsystem.
This is still preserved by this patch.
So now both ipip/xfrm4_tunnel depend on the new tunnel4.c which handles
the arbitration between the two. The order of processing is determined
by a simple integer which ensures that ipip gets processed before
xfrm4_tunnel.
The situation for ICMP handling is a little bit more complicated since
we may not have enough information to determine who it's for. It's not
a big deal at the moment since the xfrm ICMP handlers are basically
no-ops. In future we can deal with this when we look at ICMP caching
in general.
The user-visible change to this is the removal of the TUNNEL Kconfig
prompts. This makes sense because it can only be used through IPCOMP
as it stands.
The addition of the new modules shouldn't introduce any problems since
module dependency will cause them to be loaded.
Oh and I also turned some unnecessary pskb's in IPv6 related to this
patch to skb's.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 3041 describes an algorithm to generate random interface
identifier. In RFC 3041bis, it is allowed to use different
algorithm than one described in RFC 3041.
So, let's use our standard pseudo random algorithm to simplify
our implementation.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the protocol specific config options out to the specific protocols.
With this change net/Kconfig now starts to become readable and serve as a
good basis for further re-structuring.
The menu structure is left almost intact, except that indention is
fixed in most cases. Most visible are the INET changes where several
"depends on INET" are replaced with a single ifdef INET / endif pair.
Several new files were created to accomplish this change - they are
small but serve the purpose that config options are now distributed
out where they belongs.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Thomas Graf