sil24 softreset timeout was > 100ms (100 loops with msleep(1)), which
turned out to be too short for some devices (ASI ARAID99 2000). This
patch converts sil24 softreset waiting loop to use proper timeout
condition and lengthen the timeout to ATA_TMOUT_BOOT secs and check
interval to 100ms. Chisato Yamauchi discovered the problem and
supplied initial patch.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Chisato Yamauchi <cyamauch@plamo.linet.gr.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sata_sil24 softreset routine used to check sata_dev_present() after
SRST is complete in the hope that SRST may do some good even when
SStatus reports no device. This is okay as long as SRST timeout is
short (> 100ms in the current code) but it seems that not all SATA
devices are happy with short SRST timeout.
This patch makes softreset exit early without performing actual SRST
if SStatus reports no device in preparation for lengthening SRST
timeout.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix NULL pointer dereference detected by the Coverity checker. Kill
dev -> pdev -> dev conversion while at it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_bus_probe() didn't initialize classes[] properly with
ATA_DEV_UNKNOWN. As ->probe_reset() is allowed to leave @classes
alone when no device is present, this results in garbage class values.
ATM, the only affected driver is ata_piix.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Preceding xfer_mask changes make the following functions unused.
ata_pio_modes(), base_from_shift(), ata_pr_blacklisted(), fgb()
Kill them. Also, as xfer_mode_str[] is now only used by
ata_mode_string(), move it into the function.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use xfer_mask helpers to determine transfer mode. This rewrite also
makes transfer mode determination done before any actual
configuration. This patch doesn't result in any functional changes.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Replace quick & dirty max transfer mode determination in
ata_dev_configure() with ata_id_xfermask(). While at it, rename
xfer_modes variable to xfer_mask and make it unsigned int for
consistency.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add ata_pack_xfermask(), ata_xfer_mask2mode(), ata_xfer_mode2mask(),
ata_xfer_mode2shift() and ata_id_xfermask(). These functions will be
used by following patches to simplify xfer_mask handling.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add ATA_BITS_*, ATA_MASK_* macros and reorder xfer_mask fields such
that higher transfer mode is placed at higher order bit. As thie
reordering breaks ata_mode_string(), this patch also rewrites
ata_mode_string().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make pio_task and atapi_packet_task use port_task.
atapi_packet_task() is moved upward such that it's right after
ata_pio_task(). This position is more natural and makes adding
prototype for ata_qc_issue_prot() unnecessary.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement port_task. LLDD's can schedule a function to be executed
with context after specified delay. libata core takes care of
synchronization against EH. This is generalized form of pio_task and
packet_task which are tied to PIO hsm implementation.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In the past I added an host attribute but unfortunately
I forgot to increase FC_HOST_NUM_ATTRS.
This is fixed with the patch. Otherwise an fibre channel
lld might run into
BUG_ON(count > FC_HOST_NUM_ATTRS);
in fc_attach_transport().
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The patch
[SCSI] SCSI core kmalloc2kzalloc
Has an incorrect piece in sr_ioctl.c; it changes buffer from kmalloc
to kzalloc, but then removes the clearing of the stack variable struct
packet_command. This, in turn leaves rubbish in the sense pointer
which the sr_do_ioctl() command then happily writes to ... oops.
Thanks to Mike Christie <michaelc@cs.wisc.edu> for spotting this.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On 02/07/2006 04:12:55 AM, Christoph Hellwig wrote:
> On Mon, Feb 06, 2006 at 08:02:21PM -0500, Willem Riede wrote:
>
> > But I will certainly help retire scsi_request. And anything else that is
> > needed to keep up with proper kernel style. Let me know what those are, if
> > you would? I'll start looking at how st has changed, and will be back with
> > any questions I may have.
>
> right now the above is the most urgent bit. What would be nice but not
> required is a conversion to the sense handling helpers, similar to what
> st got (aka using the *normalize_sense functions and then dealing with the
> parsed sense buffer instead of the raw sense data)
Ok, so here is my first take at satisfying this request.
Be warned, that beyond compiling, and checking that the new module
doesn't immediately blow up, there hasn't yet been a lot of testing.
But this should allow you to comment on the changes, and move forward
with dropping scsi_request from the kernel code.
Signed-off-by: Willem Riede <osst@riede.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The SCSI layer uses SCSI_SENSE_BUFFERSIZE (96) for the sense buffer
size, even though some other code uses "sizeof(struct request_sense)"
(which is 64 bytes). Allocate the buffer using the bigger of the two
for safety.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix polling mode panic
Cause: Race between interrupt driven and polling path in harvesting iocbs
from
the response ring.
Signed-off-by: Jamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Protect NPL lists with host lock
Symptoms: lpfc_findnode_rpi and lpfc_findnode_did can be called
outside of the discovery thread context. We have to iterate
through the NPL lists under the host lock and all add/del
operations on those lists have to be done under host lock.
Signed-off-by: Jamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix deadlock in lpfc_fdmi_tmo_handler
lpfc_fdmi_tmo_handler was calling lpfc_fdmi_cmd with the host_lock
held. lpfc_fdmi_cmd assumes the host_lock is released as it calls functions
that acquire the host_lock. lpfc_fdmi_tmo_handler acquired the host_lock to
protect access to work_hba_events. This was already checked in the worker
thread so we can remove that code completely and remove access to the
host_lock.
Signed-off-by: Jamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix performance when using multiple SLI rings
Currently the driver allocates all of its SLI command and response ring
entries to one primary ring. Other rings get little, or no, resources.
Allow more resources to be given to ring 1
Signed-off-by: Jamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
PCI hrd_type should be obtained with pci_read_config_byte() macro
Driver keys off of this field to report the proper adapter type.
The pci subsystem explicitly clears the multiport bit in the copy of
the field given the driver. Thus, to properly name the card, obtain it
from config space.
Signed-off-by: Jamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Derive supported speeds from LMT field in the READ_CONFIG
Driver was keying off internal cores. Use what the firmware reports instead.
Signed-off-by: Jamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Begin introducing the concept of sas remote devices that have an rphy
embedded. The first one (this) is a simple end device. All that an
end device really does is have port mode page parameters contained.
The next and more complex piece will be expander remote devices.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
mwdma_mask was not copied from port_info to probe_ent. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Revalidate device after transfer mode configuration. This also makes
dev->id up-to-date.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_dev_revalidate() re-reads IDENTIFY PAGE of the given device and
makes sure it's the same device as the configured one. Once it's
verified that it's the same device, @dev is configured according to
newly read IDENTIFY PAGE. Note that revalidation currently doesn't
invoke transfer mode reconfiguration.
Criteria for 'same device'
* same class (of course)
* same model string
* same serial string
* if ATA, same n_sectors (to catch geometry parameter changes)
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add @print_info argument to ata_dev_configure(). Details of
configured device is printed only when @pinfo_info is non-zero. This
patch also reorganizes device info printing for LBA case to simplify
code (necessary as @print_info adds extra nesting around it).
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In ata_dev_configure(), reinitialize parameters before configuring.
This change is for revalidation and hotplug. As ata_dev_configure()
can be entered multiple times, parameters need to be reinitialized.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Collect common host flags into SIL_DFL_HOST_FLAGS and add comments to
constants.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Kill SIL_FIFO_* and SIL_IDE2_BMDMA and replace them with proper
sil_port[] entry.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
All 3112's have m15w. Replace sil_3112_m15w with sil_3112 and flag
sil_3112 with SIL_FLAG_MOD15WRITE.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Carlos Pardo <Carlos.Pardo@siliconimage.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Rename PIIX_FLAG_IGN_PRESENT to PIIX_FLAG_IGNORE_PCS as Jeff
requested.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds support for the Promise FastTrak TX4300/TX4310 4-port PCI SATA
controllers based on the PDC40719 chip.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Now that reset and configure are converted such that they don't modify
or disable libata core data structures, reorganize ata_bus_probe() to
reflect this change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_dev_config() needs to be done everytime a device is configured.
Fold it into ata_dev_configure().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate out ata_dev_configure() from ata_dev_identify() such that
ata_dev_configure() only configures @dev according to passed in @id.
The function now does not disable device on failure, it just returns
appropirate error code.
As this change leaves ata_dev_identify() with only reading ID, calling
configure and disabling devices according to the results, this patch
also kills ata_dev_identify() and inlines the logic into
ata_bus_probe().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert dev->id from array to pointer. This is to accomodate
revalidation. During revalidation, both old and new IDENTIFY pages
should be accessible and single ->id array doesn't cut it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reimplement piix_sata_probe() such that it turns on PCS enable bits on
all avaliable ports and check present bits after a while to determine
device presence. This should help broken BIOSes. After device
presence detection is complete, PCS enable bits of unoccupied bits are
turned off unless the controller supports AHCI (ICH6/7 docs mandate
all enables bits are always set on AHCI capable controllers).
Note that PCS present bits are ignored on 6300ESB as described in the
datasheet. This should fix device detection problems reported with
the controller.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Replace combined mode handling via PIIX_COMB/COMB_PATA_P0 with proper
port map. PIIX now prints port configuration during initialization.
ATA_FLAG_SLAVE_POSS is now turned on for SATA ports only when the
slave device is actually avaliable.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add PIIX_FLAG_IGN_PRESENT and SCR flags. Thi patch doesn't cause any
functional change. To be used by later init/scr updates.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make port_info finer-grained. This patch doesn't cause any functional
change. Later init reimplementation will make use of it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
aic94xx doesn't have a use for the bay or enclosure identifiers.
Also, I think it's not going to need a get_linkerrors(), so wire up
all of these exported properties as conditional on the underlying
function support.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Tejun Heo