This adds type-checking to pm_message_t, so that people can't confuse it
with int or u32. It also allows us to fix "disk yoyo" during suspend (disk
spinning down/up/down).
[We've tried that before; since that cpufreq problems were fixed and I've
tried make allyes config and fixed resulting damage.]
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Alexander Nyberg <alexn@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On ISP24xx parts, stop execution of firmware during ISP
tear-down.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Nishanth Aravamudan <nacc@us.ibm.com>
Replace schedule_timeout() with
msleep()/msleep_interruptible() as appropriate, to guarantee the task
delays as expected.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
fc_remove_host() should only be called after a scsi_host has
been successfully added via scsi_add_host() -- any failures
while qla2xxx probing would result in an incorrect call to
fc_remove_host() during cleanup.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Export additional host information via the shost_attrs member in
the scsi_host template. Attributes include: driver version,
firmware version, ISP serial number, ISP type, ISP product ID,
HBA model name, HBA model description, PCI interconnect
information, and HBA port state.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In a corner-case failure where the request-q does not
contain enough entries for a given request, pci_unmap_sg()
would be called twice. Remove direct call and let the
failure-path logic handle the unmapping.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove unnecessary RISC pause/release barriers during
ISP24xx flash manipulation. The ISP24xx can arbitrate flash
access requests during RISC executions.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Original implementation used an overloaded bit in the EFI
parameters. The correct bit is BIT_4 of the special_options
section of NVRAM.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove redundant qla2x00_target_reset() function in favour of
the equivalent qla2x00_device_reset(). Update callers of
old function.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In an FL topology, limit port recognition to those devices
not within the same area and domain of the ISP. The
firmware will recogonize such devices during local-loop
discovery.
Some devices may respond to a PLOGI before they have
completed their fabric login or they may not be a public
device. In this case they will report:
domain == 00
area == 00
alpa == <XX>
which is valid. Exclude such devices from local loop
discovery.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Export COS information for the fc_host and fc_remote_port
objects added by the driver.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In order to efficiently utilise the ISP's IOCB
request-queue, use the dma_get_required_mask() function to
determine the use of command-type 2 or 3 IOCBs when queueing
SCSI commands. This applies to ISP2[123]xx chips only, as
the ISP24xx uses command-type 7 IOCBs which use 64bit DSDs.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
#include of C files and macro tricks to rename symbols are evil and just
cause trouble. Let's doublicate the two functions as they're going to
go away soon enough anyway.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This was noticed by Doug Bazamic and the fix found by Mark Salyzyn at
Adaptec.
There was an error in the BUG_ON() statement that validated the
calculated fib size which can cause the driver to panic.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adopts the same solution as proposed by Kai M. in
a post titled: "[PATCH] SCSI tape signed/unsigned fix".
The fix is in a function that the sg driver borrowed from
the st driver so its maintenance is a little easier if
the functions remain the same after the fix.
- change nr_pages type from unsigned to signed so errors
from get_user_pages() call are properly handled
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
reported by Doug Gilbert and fixed by him in sg.c (see [PATCH] sg direct
io/mmap oops). Doug fixed the comparison in sg.c. This fix for st.c does not
touch the comparison but makes both arguments signed to remove the
problem. The new code is adapted from linux/fs/bio.c.
Signed-off-by: Kai Makisara <kai.makisara@kolumbus.fi>
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The idea behind a RAID class is to provide a uniform interface to all
RAID subsystems (both hardware and software) in the kernel.
To do that, I've made this class a transport class that's entirely
subsystem independent (although the matching routines have to match per
subsystem, as you'll see looking at the code). I put it in the scsi
subdirectory purely because I needed somewhere to play with it, but it's
not a scsi specific module.
I used a fusion raid card as the test bed for this; with that kind of
card, this is the type of class output you get:
jejb@titanic> ls -l /sys/class/raid_devices/20\:0\:0\:0/
total 0
lrwxrwxrwx 1 root root 0 Aug 16 17:21 component-0 -> ../../../devices/pci0000:80/0000:80:04.0/host20/target20:1:0/20:1:0:0/
lrwxrwxrwx 1 root root 0 Aug 16 17:21 component-1 -> ../../../devices/pci0000:80/0000:80:04.0/host20/target20:1:1/20:1:1:0/
lrwxrwxrwx 1 root root 0 Aug 16 17:21 device -> ../../../devices/pci0000:80/0000:80:04.0/host20/target20:0:0/20:0:0:0/
-r--r--r-- 1 root root 16384 Aug 16 17:21 level
-r--r--r-- 1 root root 16384 Aug 16 17:21 resync
-r--r--r-- 1 root root 16384 Aug 16 17:21 state
So it's really simple: for a SCSI device representing a hardware raid,
it shows the raid level, the array state, the resync % complete (if the
state is resyncing) and the underlying components of the RAID (these are
exposed in fusion on the virtual channel 1).
As you can see, this type of information can be exported by almost
anything, including software raid.
The more difficult trick, of course, is going to be getting it to
perform configuration type actions with writable attributes.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Don't bother calling a hook, to call our own module, to call a helper
than simply calls ionumap().
If you unroll all that convolution, you get a simple kfree()+iounmap()
pair of calls.
ATAPI is getting close to being ready. To increase exposure, we enable
the code in the upstream kernel, but default it to off (present
behavior). Users must pass atapi_enabled=1 as a module option (if
module) or on the kernel command line (if built in) to turn on
discovery of their ATAPI devices.
Create vio_bus_ops so that we just pass a structure to vio_bus_init
instead of three separate function pointers.
Rearrange vio.h to avoid forward references. vio.h only needs
struct device_node from prom.h so remove the include and just
declare it.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
- changes license of all code from OSL+GPL to plain ole GPL
- except for NVIDIA, who hasn't yet responded about sata_nv
- copyright holders were already contacted privately
- adds info in each driver about where hardware/protocol docs may be
obtained
- where I have made major contributions, updated copyright dates
The new bio code was incorrectly converted from stack allocated to
kmalloc'd buffer handling. There are two places where it incorrectly
uses sizeof(*sense) to get the size of the sense buffer. This
actually produces one, so no sense data was ever getting back, causing
failure in things like disk spin up.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The 3ware emulated commands all expect they are executing in the
use_sg == 0 case, which isn't true either in the block layer rework or
an SG_IO ioctl.
Fix this by adding the correct kmapping of the first element in the sg
list.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Older gcc's require variable definitions at the beginning of a block.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
I also tinkered with it's sense recognition routines to make them take
scsi_sense_hdr structures instead of raw sense data.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This follows almost the identical model to sd, except that there's one
ioctl which returns raw sense data, so it had to use scsi_execute()
instead.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This one removes struct scsi_request entirely from sd. In the process,
I noticed we have no callers of scsi_wait_req who don't immediately
normalise the sense, so I updated the API to make it take a struct
scsi_sense_hdr instead of simply a big sense buffer.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This one's slightly more difficult. The transport class uses
REQ_FAILFAST, so another interface (scsi_execute) had to be invented to
take the extra flag. Also, the sense functions are shifted around to
allow spi_execute to place data directly into a struct scsi_sense_hdr.
With this change, there's probably a lot of unnecessary sense buffer
allocation going on which we can fix later.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
After this, we just have some drivers, all the ULDs and the SPI
transport class using scsi_wait_req().
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Here's the problem. Try to do this on 2.6.12:
- Kill udev and HAL
- Insert a CD-ROM into a SCSI or USB CD-ROM drive
- Run dd if=/dev/scd0
- cat /sys/block/sr0/size
- Eject the CD, insert a different one
- Run dd if=/dev/scd0
This is likely to do "access beyond the end of device", if you let it
- cat /sys/block/sr0/size
This shows the size of a previous CD, even though dd was supposed
to revalidate the device.
- Run dd if=/dev/scd0
The second run of dd works correctly!
The bug was introduced in 2.5.31, when Al fixes the recursive opens
in partitioning. Before, the code worked like this:
- Block layer called cdrom_open directly
- cdrom_open called sr_open
- sr_open called check_disk_change
- check_disk_change called sr_media_change
- sr_media_change did cd->needs_disk_change=1
- before returning sr_open tested cd->needs_disk_change
and called get_sector_size.
In 2.6.12, the check_disk_change is called from cdrom_open only. Thus:
- Block layer calls sr_bd_open
- sr_bd_open calls cdrom_open
- cdrom_open calls sr_open
- sr_open tests cd->needs_disk_change, which wasn't set yet; returns
- cdrom_open calls check_disk_change
- check_disk_change calls sr_media_change
- sr_media_change does cd->needs_disk_change=1, but nobody cares
Acked by: Alexander Viro <aviro@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch fixes a long term borkenness in
ibmvscsi where we were using the wrong timeout
field from the scsi command (and using the
wrong units.) Now broken by the fact that the
scsi_cmnd timeout field is gone entirely.
This only worked before because all the SCSI
targets assumed that 0 was default.
Signed-off-by: Dave Boutcher <boutcher@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
C files should include the files with the prototypes for their global
functions.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
With the removal of the spinlocking around eh calls, we need to add a
little more locking back in, otherwise we do some naked list
manipulation.
Signed-off-by: Dave Boutcher <boutcher@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch fixes the bad assumption of the aacraid driver with use_sg.
I used the 3w-xxxx driver fix as a guide for this.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Original From: Mike Christie <michaelc@cs.wisc.edu>
Add scsi_execute_req() as a replacement for scsi_wait_req()
Fixed up various pieces (added REQ_SPECIAL and caught req use after
free)
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Here's the proof of concept for this one. It converts scsi_wait_req to
do correct REQ_BLOCK_PC submission (and works nicely in my setup).
The final goal should be to eliminate struct scsi_request, but that
can't be done until the character submission paths of sg and st are also
modified.
There's some loss of functionality to this: retries are no longer
controllable (except by setting REQ_FASTFAIL) and the wait_req API needs
to be altered, but it looks very nice.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
I know that scsi procfs is legacy code but this is a fix for a memory leak.
While reading through sg.c I realized that the implementation of
/proc/scsi/sg/devices with seq_file is leaking memory due to freeing the
pointer returned by the next() iterator method. Since next() might return
NULL or an error this is wrong. This patch fixes it through using the
seq_files private field for holding the reference to the iterator object.
Here is a small bash script to trigger the leak. Use slabtop to watch
the size-32 usage grow and grow.
#!/bin/sh
while true; do
cat /proc/scsi/sg/devices > /dev/null
done
Signed-off-by: Jan Blunck <j.blunck@tu-harburg.de>
Acked-by: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix bugs for unlikely edge cases noticed by Douglas Gilbert:
- When READ(6)/WRITE(6) sector count == 0, treat it as 256 sectors
- For other READ(x)/WRITE(x), when sector count == 0, error.
We don't support successfully completing zero-length transfers at
this time.
Pavel Machek