This patch simplifies the opening and closing of host console devices and the
registration and deregistration of IRQs. The intent is to make it obvious
that an IRQ can't exist without an open file descriptor.
chan_enable will now open the channel, and when both opening and IRQ
registration are desired, this should be used. Opening only is done for the
initial console, so that interface still needs to exist.
The free_irqs_later interface is now gone. It was intended to avoid freeing
an IRQ while it was being processed. It did this, but it didn't eliminate the
possiblity of free_irq being called from an interrupt, which is bad. In its
place is a list of irqs to be freed, which is processed by the signal handler
just before exiting. close_one_chan now disables irqs.
When a host device disappears, it is just closed, and that disables IRQs.
The device id registered with the IRQ is now the chan structure, not the tty.
This is because the interrupt arrives on a descriptor associated with the
channel. This caused equivalent changes in the arguments to line_timer_cb.
line_disable is gone since it is not used any more.
The count field in the line structure is gone. tty->count is used instead.
The complicated logic in sigio_handler with freeing IRQs when necessary and
making sure its idea of the next irq is correct is now much simpler. The irq
list can't be rearranged underneath it, so it is now a simple list walk.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With Chris Wedgwood <cw@f00f.org>
Currently UML must explicitly call the UML-specific
free_irq_by_irq_and_dev() for each free_irq call it's done.
This is needed because ->shutdown and/or ->disable are only called when the
last "action" for that irq is removed.
Instead, for UML shared IRQs (UML IRQs are very often, if not always,
shared), for each dev_id some setup is done, which must be cleared on the
release of that fd. For instance, for each open console a new instance
(i.e. new dev_id) of the same IRQ is requested().
Exactly, a fd is stored in an array (pollfds), which is after read by a
host thread and passed to poll(). Each event registered by poll() triggers
an interrupt. So, for each free_irq() we must remove the corresponding
host fd from the table, which we do via this -release() method.
In this patch we add an appropriate hook for this, and remove all uses of
it by pointing the hook to the said procedure; this is safe to do since the
said procedure.
Also some cosmetic improvements are included.
This is heavily based on some work by Chris Wedgwood, which however didn't
get the patch merged for something I'd call a "misunderstanding" (the need
for this patch wasn't cleanly explained, thus adding the generic hook was
felt as undesirable).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
CC: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace one memcpy() call with overlapping source and dest arguments with
one call to memmove(), to avoid data corruption.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Jeff Dike