Currently completion of WM831x AUXADC conversions is monitored by
checking for convertor enable. Due to the mechanism used to ensure
data corruption is avoided when reading AUXADC data there may under
heavy I/O be a window where this bit has cleared but the conversion
results have not been updated. Data availability is only guaranteed
after the AUXADC data interrupt has been asserted.
Avoid this by always using the interrupt to detect completion. If the
chip IRQ is not set up then we poll the IRQ status register for up to
5ms. If it is set up then we rely on the data done interrupt with a
vastly increased timeout, failing the conversion if the interrupt is
not generated.
This also saves a register read when using interrupts.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The Janz VMOD-TTL is a MODULbus daughterboard which fits onto any MODULbus
carrier board. It essentially consists of some various logic and a Zilog
Z8536 CIO Counter/Timer and Parallel IO Unit.
The board must be physically configured with jumpers to enable a user to
drive output signals. I am only interested in outputs, so I have made this
driver as simple as possible. It only supports a very minimal subset of the
features provided by the Z8536 chip.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The Janz VMOD-ICAN3 is a MODULbus daughterboard which fits onto any
MODULbus carrier board. It is an intelligent CAN controller with a
microcontroller and associated firmware.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The Janz CMOD-IO PCI MODULbus carrier board is a PCI to MODULbus bridge,
which may host many different types of MODULbus daughterboards, including
CAN and GPIO controllers.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Reviewed-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This was used by the old, pre-genirq IRQ implementation but is no
longer required.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add platform data for timb-dma, and add it in to timb-dma
in all configurations of timberdale.
Also incremented the version number.
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch fixes three section mismatches.
WARNING: drivers/mfd/88pm860x.o(.text+0x12): Section mismatch in
reference from the function pm860x_device_exit() to the function
.devexit.text:device_irq_exit()
The function pm860x_device_exit() references a function in an exit
section.
Often the function device_irq_exit() has valid usage outside the exit
section
and the fix is to remove the __devexit annotation of device_irq_exit.
WARNING: drivers/mfd/88pm860x.o(.text+0xb0): Section mismatch in
reference from the function pm860x_device_init() to the function
.devinit.text:device_8606_init()
The function pm860x_device_init() references
the function __devinit device_8606_init().
This is often because pm860x_device_init lacks a __devinit
annotation or the annotation of device_8606_init is wrong.
WARNING: drivers/mfd/88pm860x.o(.text+0xbe): Section mismatch in
reference from the function pm860x_device_init() to the function
.devinit.text:device_8607_init()
The function pm860x_device_init() references
the function __devinit device_8607_init().
This is often because pm860x_device_init lacks a __devinit
annotation or the annotation of device_8607_init is wrong.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
I'm pretty sure that it should be + 1 here. It's an off by one, because
we start counting at zero.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This file is replaced by a cleaner version with the adding of a MFD driver for
the southbridge.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The RDC321x MFD southbridge driver will pass a reference to the
southbridge PCI device which should be used by the watchdog driver for its
operations. This patch converts the watchdog driver to use the pci_dev
pointer and make use of the base register resource which is passed along
with the platform device.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds a new GPIO driver for the RDC321x SoC GPIO controller.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds a new MFD driver for the RDC321x southbridge. This southbridge
is always present in the RDC321x System-on-a-Chip and provides access to some
GPIOs as well as a watchdog. Access to these two functions is done using the
southbridge PCI device configuration space.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fix I2C-drivers which missed setting clientdata to NULL before freeing the
structure it points to. Also fix drivers which do this _after_ the structure
was freed already.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds in the Xilinx I2C bus driver to some of the
configurations of the timberdale MFD.
It provides the I2C devices to the XIIC via platform data in a
similar way as done to the ocores driver.
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We should check for pdata being not NULL before dereferencing it.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (61 commits)
tracing: Add __used annotation to event variable
perf, trace: Fix !x86 build bug
perf report: Support multiple events on the TUI
perf annotate: Fix up usage of the build id cache
x86/mmiotrace: Remove redundant instruction prefix checks
perf annotate: Add TUI interface
perf tui: Remove annotate from popup menu after failure
perf report: Don't start the TUI if -D is used
perf: Fix getline undeclared
perf: Optimize perf_tp_event_match()
perf: Remove more code from the fastpath
perf: Optimize the !vmalloc backed buffer
perf: Optimize perf_output_copy()
perf: Fix wakeup storm for RO mmap()s
perf-record: Share per-cpu buffers
perf-record: Remove -M
perf: Ensure that IOC_OUTPUT isn't used to create multi-writer buffers
perf, trace: Optimize tracepoints by using per-tracepoint-per-cpu hlist to track events
perf, trace: Optimize tracepoints by removing IRQ-disable from perf/tracepoint interaction
perf tui: Allow disabling the TUI on a per command basis in ~/.perfconfig
...
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
leds: Add mx31moboard MC13783 led support
leds: Add mc13783 LED support
leds: leds-ss4200: fix led_classdev_unregister twice in error handling
leds: leds-lp3944: properly handle lp3944_configure fail in lp3944_probe
leds: led-class: set permissions on max_brightness file to 0444
leds: leds-gpio: Change blink_set callback to be able to turn off blinking
leds: Add LED driver for the Soekris net5501 board
leds: 88pm860x - fix checking in probe function
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging: (23 commits)
hwmon: (lm75) Add support for the Texas Instruments TMP105
hwmon: (ltc4245) Read only one GPIO pin
hwmon: (dme1737) Add SCH5127 support
hwmon: (tmp102) Don't always stop chip at exit
hwmon: (tmp102) Fix suspend and resume functions
hwmon: (tmp102) Various fixes
hwmon: Driver for TI TMP102 temperature sensor
hwmon: EMC1403 thermal sensor support
hwmon: (applesmc) Add temperature sensor labels to sysfs interface
hwmon: (applesmc) Add generic support for MacBook Pro 7
hwmon: (applesmc) Add generic support for MacBook Pro 6
hwmon: (applesmc) Add support for MacBook Pro 5,3 and 5,4
hwmon: (tmp401) Reorganize code to get rid of static forward declarations
hwmon: (tmp401) Use constants for sysfs file permissions
hwmon: (adm1031) Allow setting update rate
hwmon: Add description of the update_rate sysfs attribute
hwmon: (lm90) Use programmed update rate
hwmon: (f71882fg) Acquire I/O regions while we're working with them
hwmon: (f71882fg) Code cleanup
hwmon: (f71882fg) Use strict_stro(l|ul) instead of simple_strto$1
...
Add support for the Texas Instruments TMP105 temperature sensor
device.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti@ti.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Read only one of the GPIO pins as an analog voltage. The ADC can be
switched to a different GPIO pin at runtime, but this is not supported.
Previously, this driver would report the analog voltage of the currently
selected GPIO pin as all three GPIO voltages: in9_input, in10_input and
in11_input.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
Add support for the hardware monitoring capabilities of the SCH5127
chip to the dme1737 driver.
Signed-off-by: Juerg Haefliger <juergh@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Jeff Rickman <jrickman@myamigos.us>
Only stop the chip at driver exit if it was stopped when driver was
loaded. Leave it running otherwise.
Also restore the device configuration if probe failed, to not leave
the system in a dangling state.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Steven King <sfking@fdwdc.com>
Suspend and resume functions shouldn't overwrite the configuration
register. They should only alter the one bit they have to touch.
Also don't assume that register reads and writes always succeed.
Handle errors properly, shall they happen.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Steven King <sfking@fdwdc.com>
Fixes from my driver review:
http://lists.lm-sensors.org/pipermail/lm-sensors/2010-March/028051.html
Only the small changes are in there, more important changes will come
later separately as time permits.
* Drop the remnants of the now gone detect function
* The TMP102 has no known compatible chip
* Include the right header files
* Clarify why byte swapping of register values is needed
* Strip resolution info bit from temperature register value
* Set cache lifetime to 1/3 second
* Don't arbitrarily reject limit values; clamp as needed
* Make limit writing unconditional
* Don't check for transaction types the driver doesn't use
* Properly check for error when setting configuration
* Report error on failed probe
* Make the driver load automatically where needed
* Various other minor fixes
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Steven King <sfking@fdwdc.com>
Driver for the TI TMP102.
The TI TMP102 is similar to the LM75. It differs from the LM75 by
having a 16-bit conf register and the temp registers have a minimum
resolution of 12 bits; the extended conf register can select 13-bit
resolution (which this driver does) and also change the update rate
(which this driver currently doesn't use).
[JD: Fix tmp102_exit tag, must be __exit, not __init.]
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Provides support for the EMC1403 thermal sensor. Only reporting of values
is supported. The various Moorestown specific extras to do with thermal
alerts and the like are not in this version of the driver.
Considerably edited and tidied up by Alan Cox, plus fixes and detection
bits from Jean Delvare.
Signed-off-by: Kalhan Trisal <kalhan.trisal@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The Apple SMC uses a systematic labeling scheme for the hardware
temperature sensors. This scheme is currently hidden from
userland. Since the sensor set, and consequently the numbering,
differs between models, an extensive database of configurations is
required for an application such as fan control. This patch adds the
SMC labels to the hwmon sysfs interface, allowing applications to use
the sensors more intelligibly.
[rydberg@euromail.se: fixed error handling]
Signed-off-by: Alex Murray <murray.alex@gmail.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch adds generic support for the MacBook Pro 7 family
based on the 7,1 model.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch adds generic support for the MacBook Pro 6 family
based on the 6,2 model.
[rydberg@euromail.se: patch cleanup]
Signed-off-by: Bernhard Froemel <froemel@vmars.tuwien.ac.at>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The MacBookPro 5,3 model has two fans, whereas the 5,4 model has
only one. This patch adds explicit support for the 5,3 and 5,4 models.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Replace octal representation of file permissions by the corresponding
constants.
Signed-off-by: Andre Prendel <andre.prendel@gmx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Based on earlier work by Ira W. Snyder.
The adm1031 chip is capable of using a runtime configurable sampling rate,
using the fan filter register. Add support for reading and setting the
update rate via sysfs.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ira W. Snyder <iws@ovro.caltech.edu>
The update_rate attribute can be used by drivers to let userspace choose
the update rate of the chip, if it is configurable.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The lm90 driver programs the sensor chip to update its readings at 2 Hz
(500 ms between readings). However, the driver only does reads from the
chip at intervals of 2 * HZ (2000 ms between readings). Change the driver
update rate to the programmed update rate.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acquire the I/O region for the Super I/O chip while we're working on it.
Signed-off-by: Giel van Schijndel <me@mortis.eu>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Some code cleanup: properly use previously defined functions, rather
than duplicating their code.
Signed-off-by: Giel van Schijndel <me@mortis.eu>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Use the strict_strol and strict_stroul functions instead of simple_strol
and simple_stroul respectively in sysfs functions.
Signed-off-by: Giel van Schijndel <me@mortis.eu>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fixed several coding style issues.
Signed-off-by: Giel van Schijndel <me@mortis.eu>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The LM64 appears to be an LM63 with added GPIO lines. Add support for the
hwmon functionality - GPIO can be added at some later stage if someone
has a need for them.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
When the user passes the kernel parameter acpi_enforce_resources=lax,
the ACPI resources are no longer protected, so a native driver can
make use of them. In that case, we do not want the asus_atk0110 to be
loaded. Unfortunately, this driver loads automatically due to its
MODULE_DEVICE_TABLE, so the user ends up with two drivers loaded for
the same device - this is bad.
So I suggest that we prevent the asus_atk0110 driver from loading if
acpi_enforce_resources=lax.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Luca Tettamanti <kronos.it@gmail.com>
Cc: Len Brown <lenb@kernel.org>
* 'sfi-release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-sfi-2.6:
SFI: add sysfs interface for SFI tables.
SFI: add support for v0.81 spec
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable: (27 commits)
Btrfs: add more error checking to btrfs_dirty_inode
Btrfs: allow unaligned DIO
Btrfs: drop verbose enospc printk
Btrfs: Fix block generation verification race
Btrfs: fix preallocation and nodatacow checks in O_DIRECT
Btrfs: avoid ENOSPC errors in btrfs_dirty_inode
Btrfs: move O_DIRECT space reservation to btrfs_direct_IO
Btrfs: rework O_DIRECT enospc handling
Btrfs: use async helpers for DIO write checksumming
Btrfs: don't walk around with task->state != TASK_RUNNING
Btrfs: do aio_write instead of write
Btrfs: add basic DIO read/write support
direct-io: do not merge logically non-contiguous requests
direct-io: add a hook for the fs to provide its own submit_bio function
fs: allow short direct-io reads to be completed via buffered IO
Btrfs: Metadata ENOSPC handling for balance
Btrfs: Pre-allocate space for data relocation
Btrfs: Metadata ENOSPC handling for tree log
Btrfs: Metadata reservation for orphan inodes
Btrfs: Introduce global metadata reservation
...
Commit e9fb7631ebcd ("cpu-hotplug: introduce cpu_notify(),
__cpu_notify(), cpu_notify_nofail()") also introduced this annoying
warning:
kernel/cpu.c:157: warning: 'cpu_notify_nofail' defined but not used
when CONFIG_HOTPLUG_CPU wasn't set.
So move that helper inside the #ifdef CONFIG_HOTPLUG_CPU region, and
simplify it while at it.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6:
[SCSI] fix race in scsi_target_reap
[SCSI] aacraid: Eliminate use after free
[SCSI] arcmsr: Support HW reset for EH and polling scheme for scsi device
[SCSI] bfa: fix system crash when reading sysfs fc_host statistics
[SCSI] iscsi_tcp: remove sk_sleep check
[SCSI] ipr: improve interrupt service routine performance
[SCSI] ipr: set the data list length in the request control block
[SCSI] ipr: fix a register read to use the correct address for 64 bit adapters
[SCSI] ipr: include the resource path in the IOA status area structure
[SCSI] ipr: implement fixes for 64 bit adapter support
[SCSI] be2iscsi: correct return value in mgmt_invalidate_icds()
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (40 commits)
ext4: Make fsync sync new parent directories in no-journal mode
ext4: Drop whitespace at end of lines
ext4: Fix compat EXT4_IOC_ADD_GROUP
ext4: Conditionally define compat ioctl numbers
tracing: Convert more ext4 events to DEFINE_EVENT
ext4: Add new tracepoints to track mballoc's buddy bitmap loads
ext4: Add a missing trace hook
ext4: restart ext4_ext_remove_space() after transaction restart
ext4: Clear the EXT4_EOFBLOCKS_FL flag only when warranted
ext4: Avoid crashing on NULL ptr dereference on a filesystem error
ext4: Use bitops to read/modify i_flags in struct ext4_inode_info
ext4: Convert calls of ext4_error() to EXT4_ERROR_INODE()
ext4: Convert callers of ext4_get_blocks() to use ext4_map_blocks()
ext4: Add new abstraction ext4_map_blocks() underneath ext4_get_blocks()
ext4: Use our own write_cache_pages()
ext4: Show journal_checksum option
ext4: Fix for ext4_mb_collect_stats()
ext4: check for a good block group before loading buddy pages
ext4: Prevent creation of files larger than RLIMIT_FSIZE using fallocate
ext4: Remove extraneous newlines in ext4_msg() calls
...
Fixed up trivial conflict in fs/ext4/fsync.c
Mark Brown