SB700 supports one physical IDE channel, but SB700 SATA controller
supports combined mode. When the SATA combined mode is enabled,
two SATA ports (port4 and port5) share one IDE channel from IDE
controller, and PATA will share the other IDE channel.
Our previous patch adding SB700 IDE device ID only supports one
IDE channel, which contains bug. The attached patch fixes the bug.
Signed-off-by: "Shane Huang" <Shane.Huang@amd.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
From RFC 3493, Section 5.2:
IPV6_MULTICAST_IF
Set the interface to use for outgoing multicast packets. The
argument is the index of the interface to use. If the
interface index is specified as zero, the system selects the
interface (for example, by looking up the address in a routing
table and using the resulting interface).
This patch adds support for (index == 0) to reset the value to it's
original state, allowing the system to choose the best interface. IPv4
already behaves this way.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Acked-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch will add MODULE_ALIAS("ip6t_<modulename>") where missing,
otherwise you will get
ip6tables: No chain/target/match by that name
when xt_<modulename> is not already loaded.
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
With your description I could reproduce the bug and actually you were
completely right: the code above is incorrect. Somehow I was able to
misread RFC1122 and mixed the roles :-(:
When a connection is >>closed actively<<, it MUST linger in
TIME-WAIT state for a time 2xMSL (Maximum Segment Lifetime).
However, it MAY >>accept<< a new SYN from the remote TCP to
reopen the connection directly from TIME-WAIT state, if it:
[...]
The fix is as follows: if the receiver initiated an active close, then the
sender may reopen the connection - otherwise try to figure out if we hold
a dead connection.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Tested-by: Krzysztof Piotr Oledzki <ole@ans.pl>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the corgi backlight driver to a more generic version
so it can be reused by other code rather than being Zaurus/PXA
specific.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
This patch adds support for powering on and off the Samsung LTV350QV LCD
panel via SPI. The driver responds to framebuffer power management, it
powers off the panel on reboot/halt/poweroff. It can also be controlled
through sysfs. The panel is powered up when the module is loaded, and off
when the module is unloaded. Verified on AVR32 STK1000.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
After fixing the too small memory allocation in cr_backlight_probe()
from drivers/video/backlight/cr_bllcd.c
(commit e3bbb3f053) I noticed that the
Coverity checker also thought there were a few memory leaks in there.
I took a closer look and confirmed that there were indeed several
leaks.
At the start of the function we allocate storage for a
'struct cr_panel' and store the pointer in a variable named 'crp'.
Then we call pci_get_device() and pci_read_config_byte() and if
either of them fail we return without freeing the memory allocated
for the 'struct cr_panel'. These two leaks are easy to fix since we
don't even use 'crp' for anything up to this point, so I simply
moved the allocation further down in the function so it only happens
just before we actually need it.
A bit further down we call backlight_device_register() and store the
result in 'crp->cr_backlight_device'. In case of error we return
'crp->cr_backlight_device' from the function, thus leaking 'crp'
itself. The same thing happens with the call to lcd_device_register().
To fix these two leaks I declare two new pointers to hold the return
values, so that in case of error we can return the pointer (as before)
but without leaking 'crp'.
This version of the patch also adds missing
backlight_device_unregister() / lcd_device_unregister() / pci_dev_put()
calls to error paths.
Thanks to Richard Purdie <rpurdie@rpsys.net> for noticing.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
This patch makes two needlessly global structs static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Update Cobalt Qube series front LED support.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
The leds-cobalt driver only supports the Coable Qube series
(not included in Cobalt Raq series).
Rename the driver and update Kconfig/Makefile.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Acked-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
This patch adds basic support for the new 405EX and the AMCC eval board
Kilauea to arch/powerpc.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
I get a compilation error in sglist-arch branch
with BLK_DEV_IO_TRACE=n:
CC block/compat_ioctl.o
/usr0/export/dev/bharrosh/git/pub/linux-2.6-block/block/compat_ioctl.c: In
function ?compat_blk_trace_setup?:
/usr0/export/dev/bharrosh/git/pub/linux-2.6-block/block/compat_ioctl.c:568:
error: expected expression before ?do?
make[2]: *** [block/compat_ioctl.o] Error 1
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
All ppc32 systems except PReP and 8xx are capable of handling 3G of user
address space. Old legacy had set this to 2GB and no one has bothered to
fix it.
8xx could be bumped up to 3GB if its SW TLB miss handlers were fixed up
to properly determine kernel/user addresses.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move to using PAGE_OFFSET instead of TASK_SIZE or KERNELBASE value on
6xx/40x/44x/fsl-booke to determine if the faulting address is a kernel or
user space address. This mimics how the macro is_kernel_addr() works.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Using weight32() to determine if a value is a power of 2 is a rather
heavi weight solution. The classic idiom is (x & (x - 1)) == 0, but
the kernel already provide a is_power_of_2 function for it.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Change the $(ARCH) dependency to $(SRCARCH) to honor the x86
namespace for i386 and x86_64.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
asm-powerpc/mpc85xx.h was really a hold over from arch/ppc. Now that
more decoupling has occurred we can remove <asm/mpc85xx.h> and some of
its legacy.
As part of this we moved the definition of CPM_MAP_ADDR into cpm2.h
for 85xx platforms. This is a stop gap until drivers stop using
CPM_MAP_ADDR.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We don't use any CPM devices on these boards, but the muram node on these
chips is different from the 8560, so it's helpful to people working with
custom boards based on these chips.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In testing the new clocksource and clockevent code on a PPC601
processor, I discovered that the clockevent multiplier value for the
decrementer clockevent was overflowing. Because the RTCL register in
the 601 effectively counts at 1GHz (it doesn't actually, but it
increases by 128 every 128ns), and the shift value was 32, that meant
the multiplier value had to be 2^32, which won't fit in an unsigned
long on 32-bit. The same problem would arise on any platform where
the timebase frequency was 1GHz or more (not that we actually have any
such machines today).
This fixes it by reducing the shift value to 16. Doing the
calculations with a resolution of 2^-16 nanoseconds (15 femtoseconds)
should be quite adequate. :)
Signed-off-by: Paul Mackerras <paulus@samba.org>
On old powermacs, we sometimes set the decrementer to 1 in order to
trigger a decrementer interrupt, which we use to handle an interrupt
that was pending at the time when it was re-enabled. This was causing
the decrementer clock event device to call the event function for the
next event early, which was causing problems when high-res timers were
not enabled.
This fixes the problem by recording the timebase value at which the
next event should occur, and checking the current timebase against the
recorded value in timer_interrupt. If it isn't time for the next
event, it just reprograms the decrementer and returns.
This also subtracts 1 from the value stored into the decrementer,
which is appropriate because the decrementer interrupts on the
transition from 0 to -1, not when the decrementer reaches 0.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some IBM machines supply a "logical" PVR (processor version register)
value in the device tree in the cpu nodes rather than the real PVR.
This is used for instance to indicate that the processors in a POWER6
partition have been configured by the hypervisor to run in POWER5+
mode rather than POWER6 mode. To cope with this, we call identify_cpu
a second time with the logical PVR value (the first call is with the
real PVR value in the very early setup code).
However, POWER5+ machines can also supply a logical PVR value, and use
the same value (the value that indicates a v2.04 architecture
compliant processor). This causes problems for code that uses the
performance monitor (such as oprofile), because the PMU registers are
different in POWER6 (even in POWER5+ mode) from the real POWER5+.
This change works around this problem by taking out the PMU
information from the cputable entries for the logical PVR values, and
changing identify_cpu so that the second call to it won't overwrite
the PMU information that was established by the first call (the one
with the real PVR), but does update the other fields. Specifically,
if the cputable entry for the logical PVR value has num_pmcs == 0,
none of the PMU-related fields get used.
So that we can create a mixed cputable entry, we now make cur_cpu_spec
point to a single static struct cpu_spec, and copy stuff from
cpu_specs[i] into it. This has the side-effect that we can now make
cpu_specs[] be initdata.
Ultimately it would be good to move the PMU-related fields out to a
separate structure, pointed to by the cputable entries, and change
identify_cpu so that it saves the PMU info pointer, copies the whole
structure, and restores the PMU info pointer, rather than identify_cpu
having to list all the fields that are *not* PMU-related.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As explained on:
http://www.avrfreaks.net/index.php?nameÿphpBB2&fileÿewtopic&tS307
If the current process is preempted before it can copy RAR_SUP and
RSR_SUP both register are lost and the process will segfault as soon
as it return from the syscall since the return adress will be
corrupted.
This patch disable IRQ as soon as we enter the syscall path and
reenable them when the copy is done.
In the interrupt handlers, check if we are interrupting the srrf
instruction, if so disable interrupts and return. The interrupt
handler will be re-called immediatly when the interrupts are
reenabled.
After some stressing workload:
- find / > /dev/null in loop
- top (in ssh)
- ping -f avr32
The segfaults are not seen anymore.
Signed-off-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The implementation of __builtin_xchg() in at least some versions of
avr32 gcc is buggy. Rather than find out exactly which versions that
have this bug, let's just avoid the problem altogether by implementing
xchg() in inline assembly.
Also, in most architectures, xchg() seems to imply a memory barrier,
while the existing avr32 implementation did not. This patch also fixes
that discrepancy.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Make the NGW100 bitbang i2c use open drain signaling.
Also, speed it up, so it's closer to 100 kHz ... the code paths seem
to be long enough that the udelay isn't dominating bit times. The
peak bit rate I observed was around 125 kHz, but that's with large
delays (usually before ACK/NAK) which hold the overall rate down to
around 80 kHz (call it 100 usec/byte on average).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Ignore a few syscalls that are irrelevant because they're either old,
depends on NUMA or depends on SMP.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This patch makes the SMC configuration take timings in clock cycles
instead of nanoseconds. A function to calculate timings in clock
cycles is added.
This patch removes the rounding troubles of the previous SMC
configuration method.
[hskinnemoen@atmel.com: fix atstk1002/atngw100 flash config]
Signed-off-by: Kristoffer Nyborg Gregertsen <gregerts@stud.ntnu.no>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Don't allow cpu hotplug on systems lacking XICS interrupt controller
(i.e. with an MPIC interrupt controller), since the current pSeries
platform code is hardcoded for XICS.
This works around the bug reported by Paul Mackerras where the
disable_nonboot_cpus() call recently added to the shutdown path will
cause an oops on older pSeries machines.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We no longer initialise the name and owner fields of the
of_platform_driver, but use the fields of the embedded device_driver's
name field instead.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This way we only have entries in the device tree for disks that actually
exist. A slight complication is that disks may be attached to LPARs
at runtime.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now we will only have entries in the device tree for the actual existing
devices (including their OS/400 properties). This way viotape.c gets
all the information about the devices from the device tree.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now we will only have entries in the device tree for the actual existing
devices (including their OS/400 properties). This way viocd.c gets all
the information about the devices from the device tree.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It was only being used to carry around dma_iommu_ops and vio_iommu_table
which we can use directly instead. This also means that vio_bus_device
doesn't need to refer to them either.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We don't need to keep a lump of dma coherent memory around for the life
of the module.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove vio_dma_ops declaration (since it no longer exists) and some
unused fields from struct vio_driver.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There is no good reason for board platform code to mess with the
ROOT_DEV. Remove it from all in-tree platforms except powermac.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This allows platforms which don't have anything to do at setup_arch time
(like a bunch of the 4xx platforms) to eliminate an empty setup_arch hook.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Given the existing "retain_initrd" boot-time parameter defined in
init/initramfs.c, there appears to be no need for the equivalent
"keepinitrd" parameter.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
I don't think the dma_sync_*_for_cpu ever did anything useful. We
flush the relevant cache lines when mapping the buffer or when calling
dma_sync_*_for_device(), and the CPU isn't allowed to touch the buffer
after that.
In other words, if these functions actually have anything to flush
from the caches, we're already in trouble.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Shane Huang