this implements autosuspend for usb printers. It compiles and is tested.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added a kernel module (gtco) to the USB Input subsystem. This kernel
module adds support for all GTCO CalComp USB InterWrite School products.
Signed-off-by: Jeremy A. Roberson <jroberson@gtcocalcomp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch ensures that the device is turned on when inserted into the system.
It also adds more VID/PIDs and matches the N_OUT_URB with the airprime driver.
Signed-off-by: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This identifies the driver for the Atmel HUSB2 Device Controller,
as integrated into the first AVR32 chip, the AT32AP700.
From: Hvard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as837) fixes several mistakes in the AIO interface of the
gadgetfs driver:
The ki_retry method is not supposed to do a put on the kiocb.
The extra call to aio_put_req() causes memory corruption.
(Note: This call was removed before, by patch as691, and then
mysteriously re-introduced later.)
Even if a read transfer is cancelled, we can and should send
to the user all the data that did manage to get transferred.
Testing for AIO cancellation in the I/O completion handler
is both racy and (now) unnecessary. aio_complete() does its
own checking, in a safe manner.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Resolve an initizlization issue that could come up if the userspace
driver wrote invalid descriptors to a dual-speed device.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This resolves a race in gadgetfs associated with changing device/ep0
when processing control requests. The fix is to change that state
earlier, when the control response is issued, so there's no window
in which userspace could see the wrong state; and enlarge the scope
of the spinlock during the ep0 request completion handler.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This simplifies event reading by eliminating arithmetic and being
more direct/obvious, and tweaks some debug messages slightly.
The math elimination will change timings, sometimes enough to
allow a race to appear.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Minor gadgetfs cleanups:
- EP0 state constants become consistently STATE_DEV_* rather than
sometimes omitting the "DEV_"; STATE_EP_* were already consistent.
- Comment that ep0 state is protected by the spinlock, and update
code that was neglecting that rule.
None of this is expected to change behavior.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- fix an error code returned if a device has been disconnected
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- take BKL before looking up a driver to associate with a device to make
sure the module is not unloaded after looking up but before association
& bumping module count
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- introduce a spinlock for serial_table to eliminate the window between
looking up a device and getting a reference
- delay inscription of a new device into serial_table until it is fully
initialised
- make sure disconnect() kills all URBs to avoid leckage across a soft unbind
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
At least the Keyspan USA-19HS USB-to-serial converter supports
two different configurations, one where the input endpoints
have interrupt transfer type and one where they are bulk endpoints.
The default UHCI configuration uses the interrupt input endpoints.
The keyspan driver, OTOH, assumes that the device has only bulk
endpoints (all URBs are initialized by calling usb_fill_bulk_urb
in keyspan.c/ keyspan_setup_urb). This causes the interval field
of the input URBs to have a value of zero instead of one, which
'accidentally' worked with Linux at least up to 2.6.17.11 but
stopped to with 2.6.18, which changed the UHCI support code handling
URBs for interrupt endpoints. The patch below modifies to driver to
initialize its input URBs either as interrupt or as bulk URBs,
depending on the transfertype contained in the associated endpoint
descriptor (only tested with the default configuration) enabling
the driver to again receive data from the serial converter.
Greg K-H reworked the patch.
Signed-off-by: Rainer Weikusat <rweikusat@sncag.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The whole approach is simply wrong. Forking a thread means that
- errors are ignored
- locking is ignored
Doing this correctly would require major surgery for questionable benefit.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This updates the AT91 UDC driver's handling of wakeup events:
- Fix a bug in the original scheme, which was never updated after
the {enable,disable}_irq_wake() semantics were updated to address
refcounting issues (i.e. behave for shared irqs).
- Couple handling of both type of wakeup events, to be more direct. The
controller can be source of wakeup events for cases like bus reset
and USB resume. On some boards, VBUS sensing is also IRQ driven.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as710) adds a sysfs class-device attribute file named
"companion" for EHCI controllers. The file contains a list of port
numbers that are dedicated to the companion controller; by writing a
port number to the file the user can force a high-speed device
attached directly to the computer to run at full speed. (As far as I
know it is not possible to do this for a device attached to an
external hub.) A port is removed from the file by writing the
negative of its port number.
Several users have asked for this facility and it seems like a useful
thing to have. Every now and then one runs across a device which
behaves much better at full speed than at high speed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as709) changes the way ehci-hcd presents port status
values for ports owned by the companion controller. It no longer
hides the information; in particular, it allows the core to see the
disconnect event that occurs when a full- or low-speed device is
switched over to the companion. This is required for the next patch
in this series.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as708) introduces a local variable to hold the port
status-register address in ehci-hub.c. There's not much improvement
in the object code, but it sure is a lot easier to read.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as841) removes from usbcore a couple of support routines
meant to help with bandwidth allocation. With the changes to uhci-hcd
in the previous patch, these routines are no longer used anywhere.
Also removed is the CONFIG_USB_BANDWIDTH option; it no longer does
anything and is no longer needed since the HCDs now handle bandwidth
issues correctly.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as840) fixes the bandwidth allocation mechanism in
uhci-hcd. It has never worked correctly.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB OHCI driver bus glue for the PS3 game console.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Restructure the ohci_hcd_mod_init error handling code in to better support
the multiple platform drivers. This does not change the functionality.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the USB HID quirk HID_QUIRK_SONY_PS3_CONTROLLER. This sends an
HID_REQ_GET_REPORT to the the PS3 controller to put the device into
'operational mode'.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB EHCI driver bus glue for the PS3 game console.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this implements enough ethtool support to make NetworkManager happy.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- implements suspend when the network interface is down
- fixes a typo in comments
- adds debugging output for power management
- fixes a compiler warning
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Gadgetfs had a mode in which endpoint descriptors were written by the user
program before connection. This mode had some bugs, and hasn't seen much
(if any) use. This patch removes that mode, leaving the mode of operation
where the user program waits for endpoint 0 to report a SET_CONFIGURATION,
and only then configures the endpoints.
From: "Phil Endecott" <spam_from_usb_devel@chezphil.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove some whitespace bugs in gadgetfs (mostly from someone's
patch updating the AIO support).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The attached patch fixes the unbalanced calls to enable_irq_wake() and
disable_irq_wake() in the AT91 USB Host driver.
It should resolve these kernel messages:
Unbalanced IRQ x wake disable
BUG: warning at kernel/irq/manage.c:167/set_irq_wake()
(The original code was debugged before a bug in the genirq wakeup irq
logic was fixed by adding the IRQ wake enable/disable refcounting.
Not all code yet uses the bugfixed model.)
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as835) removes from usb-storage the code which sets all
devices to a SCSI level of at least SCSI-2. The original reasons for
doing this no longer apply, and in fact it prevents certain kinds of
ATA pass-thru commands from being used.
The patch also marks CB and CBI devices that are SCSI-0 (legacy SCSI)
as being single-LUN, since the combined SCSI-over-USB transport
protocol has no way to convey LUN information to these devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Isochronous queues don't need a dummy TD because the Queue Header
isn't managed by the hardware. This patch (as836) removes the
unnecessary dummy TDs.
The patch also fixes a long-standing typo in a comment (a "don't" was
missing -- potentially very confusing!).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as768) improves the debugging checks for the uhci-hcd
frame list. The number of entries displayed is limited to 10, and the
driver now checks for the correct Skeleton QH link value at the end of
each chain of Isochronous TDs. The code to compute these link values
is now used in two spots, so it is moved into its own separate
subroutine.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I overlooked one. Setting the flag and killing the URBs must be under the lock
so that no URB is submitted after usb_kill_urb()
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a new, "binary" API in addition to the old, text API usbmon
had before. The new API allows for less CPU use, and it allows to capture
all data from a packet where old API only captured 32 bytes at most. There
are some limitations and conditions to this, e.g. in case someone constructs
a URB with 1GB of data, it's not likely to be captured, because even the
huge buffers of the new reader are finite. Nonetheless, I expect this new
capability to capture all data for all real life scenarios.
The downside is, a special user mode application is required where cat(1)
worked before. I have sample code at http://people.redhat.com/zaitcev/linux/
and Paolo Abeni is working on patching libpcap.
This patch was initially written by Paolo and later I tweaked it, and
we had a little back-and-forth. So this is a jointly authored patch, but
I am submitting this I am responsible for the bugs.
Signed-off-by: Paolo Abeni <paolo.abeni@email.it>
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added a function to check if an endpoint is a control endpoint.
There were similar functions for bulk, interrupt, and isoc,
but not for control endpoints.
Signed-off-by: Sarah Bailey <saharabeara@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Went looking through some usb stuff and found some unnecessary casts in
file_storage.c This is part of the KernelJanitors TODO list.
Signed-off-by: John Daiker <daikerjohn@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While adding the dynamic-id support to usb serial I found a small bug in
the air cable driver:
Adds module and name information to the usb_serial_driver instance
of aircable. So the aircable driver is correctly shown under
/sys/bus/usb-serial/drivers/aircable and has the module link.
Signed-off-by: Johannes Hölzl <johannes.hoelzl@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Every usb serial driver should have a pointer to the corresponding usb driver.
So the usb serial core can add a new id not only to the usb serial driver, but
also to the usb driver.
Also the usb drivers of ark3116, mos7720 and mos7840 missed the flag
no_dynamic_id=1. This is added now.
Signed-off-by: Johannes Hölzl <johannes.hoelzl@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Thanks to Johannes Hölzl <johannes.hoelzl@gmx.de> for fixing a few
things and getting it all working properly.
This adds support for dynamic usb ids to the usb serial core. The file
"new_id" will show up under the usb serial driver, not the usb driver
associated with the usb-serial driver (yeah, it can be a bit confusing
at first glance...)
This patch also modifies the USB core to allow the usb-serial core to
reuse much of the dynamic id logic.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Johannes Hölzl <johannes.hoelzl@gmx.de>
PPC embedded systems can have a ohci controller builtin. In the
new model, it will end up as a driver on the of_platform bus,
this patches takes care of them.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The previous model had the module_init & module_exit function in the
bus glue .c files themselves. That's a problem if several glues need
to be selected at once and the driver is built has module. This case
is quite common in embedded system where you want to handle both the
integrated ohci controller and some extra controller on PCI.
The ohci-hcd.c file now provide the module_init & module_exit and
appropriate driver registering/unregistering is done conditionally,
using #ifdefs.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Windows Mobile 5 based devices described as supporting "ActiveSync":
- Speak RNDIS but lack the CDC and union descriptors. This patch
updates the cdc ethernet code to fake ACM descriptors we need.
- Require RNDIS_MSG_QUERY messages to include a buffer of the size the
response should generate. This patch updates the rndis host code to
pass this will-be-ignored data.
The resulting RNDIS host code has been reported to work with several
WM5 based devices.
(Note that a fancier patch is available at synce.sf.net.)
Some bugfixes, affecting not just ActiveSync:
(a) when cleaning up after RNDS init fails, scrub the second interface
just like cdc_ether does, so disconnect won't oops.
(b) handle peripherals that use the pad-to-end-of-packet option; some
devices can't talk to us if that option doesn't work.
(c) when choosing configurations, don't forget about an RNDIS config
just because the RNDIS driver is dynamically linked.
Cleanup, streamlining, bugfixes, Kconfig, and matching hub driver update.
Also for paranoia's sake, refuse to talk to something that looks like a
real modem instead of RNDIS.
Signed-off-by: Ole Andre Vadla Ravnaas <oleavr@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It turns out that minor tweaks to the "CDC Subset" support in the Ethernet
gadget driver, just updating a config descriptor, let it be automagically
recognized by a Windows driver supported by MCCI.
This patch adds those descriptors, so systems using PXA 255 processors
(like Gumstix etc) can interop with those commercial MS-Windows drivers.
This is a Good Thing since Microsoft's RNDIS code has bugginess issues,
which are unfortunately compounded by "won't fix" issues as well as "the
published specs are incomplete and wrong" issues. Being able to talk to
the MCCI driver gives Windows users another connectivity option. (MCCI
also has CDC Ethernet drivers, which can help most non-PXA processors.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as830) removes some unnecessary error checking. According
to the kerneldoc, schedule_work() can't fail.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update /proc/bus/usb/devices output to report active altsettings.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It should hopefully fix the list corruption bug on:
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=214402
Add a missing INIT_LIST_HEAD()
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this makes the rio500 misc usb driver use mutexes and turns uninterruptible
sleep into interruptible sleep where the semantics are not affected.
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The patch removes unneeded void * casts for the following (void *) pointers:
- struct file: private_data
The patch also contains some whitespace and coding style cleanups in the
relevant areas.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum