kernel_samsung_sm7125/Documentation/sound/oss/Wavefront

	     An OSS/Free Driver for WaveFront soundcards
	       (Turtle Beach Maui, Tropez, Tropez Plus)

		     Paul Barton-Davis, July 1998

			  VERSION 0.2.5

Driver Status
-------------

Requires: Kernel 2.1.106 or later (the driver is included with kernels
2.1.109 and above)
	  
As of 7/22/1998, this driver is currently in *BETA* state. This means
that it compiles and runs, and that I use it on my system (Linux
2.1.106) with some reasonably demanding applications and uses.  I
believe the code is approaching an initial "finished" state that
provides bug-free support for the Tropez Plus.

Please note that to date, the driver has ONLY been tested on a Tropez
Plus. I would very much like to hear (and help out) people with Tropez
and Maui cards, since I think the driver can support those cards as
well. 

Finally, the driver has not been tested (or even compiled) as a static
(non-modular) part of the kernel. Alan Cox's good work in modularizing
OSS/Free for Linux makes this rather unnecessary.

Some Questions
--------------

**********************************************************************
0) What does this driver do that the maui driver did not ?
**********************************************************************

* can fully initialize a WaveFront card from cold boot - no DOS 
          utilities needed
* working patch/sample/program loading and unloading (the maui
      driver didn't document how to make this work, and assumed
      user-level preparation of the patch data for writing
      to the board. ick.)
* full user-level access to all WaveFront commands
* for the Tropez Plus, (primitive) control of the YSS225 FX processor
* Virtual MIDI mode supported - 2 MIDI devices accessible via the
          WaveFront's MPU401/UART emulation. One
	  accesses the WaveFront synth, the other accesses the
	  external MIDI connector. Full MIDI read/write semantics
	  for both devices.
* OSS-compliant /dev/sequencer interface for the WaveFront synth,
	  including native and GUS-format patch downloading.
* semi-intelligent patch management (prototypical at this point)

**********************************************************************
1) What to do about MIDI interfaces ?
**********************************************************************

The Tropez Plus (and perhaps other WF cards) can in theory support up
to 2 physical MIDI interfaces. One of these is connected to the
ICS2115 chip (the WaveFront synth itself) and is controlled by
MPU/UART-401 emulation code running as part of the WaveFront OS.  The
other is controlled by the CS4232 chip present on the board. However,
physical access to the CS4232 connector is difficult, and it is
unlikely (though not impossible) that you will want to use it.

An older version of this driver introduced an additional kernel config
variable which controlled whether or not the CS4232 MIDI interface was
configured. Because of Alan Cox's work on modularizing the sound
drivers, and now backporting them to 2.0.34 kernels, there seems to be
little reason to support "static" configuration variables, and so this
has been abandoned in favor of *only* module parameters. Specifying
"mpuio" and "mpuirq" for the cs4232 parameter will result in the
CS4232 MIDI interface being configured; leaving them unspecified will
leave it unconfigured (and thus unusable).

BTW, I have heard from one Tropez+ user that the CS4232 interface is
more reliable than the ICS2115 one. I have had no problems with the
latter, and I don't have the right cable to test the former one
out. Reports welcome.

**********************************************************************
2) Why does line XXX of the code look like this .... ?
**********************************************************************

Either because it's not finished yet, or because you're a better coder
than I am, or because you don't understand some aspect of how the card
or the code works. 

I absolutely welcome comments, criticisms and suggestions about the
design and implementation of the driver. 

**********************************************************************
3) What files are included ?
**********************************************************************

   drivers/sound/README.wavefront       -- this file

   drivers/sound/wavefront.patch	-- patches for the 2.1.106 sound drivers
					   needed to make the rest of this work
				           DO NOT USE IF YOU'VE APPLIED THEM 
					   BEFORE, OR HAVE 2.1.109 OR ABOVE

   drivers/sound/wavfront.c             -- the driver
   drivers/sound/ys225.h                -- data declarations for FX config
   drivers/sound/ys225.c                -- data definitions for FX config
   drivers/sound/wf_midi.c              -- the "uart401" driver 
   				              to support virtual MIDI mode.
   include/wavefront.h                  -- the header file
   Documentation/sound/oss/Tropez+          -- short docs on configuration

**********************************************************************
4) How do I compile/install/use it ?
**********************************************************************

PART ONE: install the source code into your sound driver directory

  cd <top-of-your-2.1.106-code-base-e.g.-/usr/src/linux>
  tar -zxvf <where-you-put/wavefront.tar.gz>

PART TWO: apply the patches

     DO THIS ONLY IF YOU HAVE A KERNEL VERSION BELOW 2.1.109
     AND HAVE NOT ALREADY INSTALLED THE PATCH(ES).

  cd drivers/sound
  patch < wavefront.patch

PART THREE: configure your kernel

  cd <top of your kernel tree>
  make xconfig (or whichever config option you use)

         - choose YES for Sound Support	      
         - choose MODULE (M) for OSS Sound Modules
         - choose MODULE(M) to YM3812/OPL3 support
	 - choose MODULE(M) for WaveFront support
	 - choose MODULE(M) for CS4232 support

	 - choose "N" for everything else (unless you have other
	      soundcards you want support for)


   make boot
   .
   .
   .
   <whatever you normally do for a kernel install>
   make modules
   .
   .
   .
   make modules_install

Here's my autoconf.h SOUND section:

/*
 * Sound
 */
#define CONFIG_SOUND 1
#undef  CONFIG_SOUND_OSS
#define CONFIG_SOUND_OSS_MODULE 1
#undef  CONFIG_SOUND_PAS
#undef  CONFIG_SOUND_SB
#undef  CONFIG_SOUND_ADLIB
#undef  CONFIG_SOUND_GUS
#undef  CONFIG_SOUND_MPU401
#undef  CONFIG_SOUND_PSS
#undef  CONFIG_SOUND_MSS
#undef  CONFIG_SOUND_SSCAPE
#undef  CONFIG_SOUND_TRIX
#undef  CONFIG_SOUND_MAD16
#undef  CONFIG_SOUND_WAVEFRONT
#define CONFIG_SOUND_WAVEFRONT_MODULE 1
#undef  CONFIG_SOUND_CS4232
#define CONFIG_SOUND_CS4232_MODULE 1
#undef  CONFIG_SOUND_MAUI
#undef  CONFIG_SOUND_SGALAXY
#undef  CONFIG_SOUND_OPL3SA1
#undef  CONFIG_SOUND_SOFTOSS
#undef  CONFIG_SOUND_YM3812
#define CONFIG_SOUND_YM3812_MODULE 1
#undef  CONFIG_SOUND_VMIDI
#undef  CONFIG_SOUND_UART6850
/*
 * Additional low level sound drivers
 */
#undef  CONFIG_LOWLEVEL_SOUND

************************************************************
6) How do I configure my card ?
************************************************************

You need to edit /etc/modprobe.conf. Here's mine (edited to show the
relevant details):

  # Sound system
  alias char-major-14-* wavefront
  alias synth0 wavefront
  alias mixer0 cs4232
  alias audio0 cs4232
  install wavefront /sbin/modprobe cs4232 && /sbin/modprobe -i wavefront && /sbin/modprobe opl3
  options wavefront io=0x200 irq=9
  options cs4232 synthirq=9 synthio=0x200 io=0x530 irq=5 dma=1 dma2=0
  options opl3 io=0x388

Things to note: 

       the wavefront options "io" and "irq" ***MUST*** match the "synthio"
       and "synthirq" cs4232 options.

       you can do without the opl3 module if you don't
       want to use the OPL/[34] FM synth on the soundcard

       the opl3 io parameter is conventionally not adjustable.
       In theory, any not-in-use IO port address would work, but
       just use 0x388 and stick with the crowd.

**********************************************************************
7) What about firmware ?
**********************************************************************

Turtle Beach have not given me permission to distribute their firmware
for the ICS2115. However, if you have a WaveFront card, then you
almost certainly have the firmware, and if not, its freely available
on their website, at:

   http://www.tbeach.com/tbs/downloads/scardsdown.htm#tropezplus 

The file is called WFOS2001.MOT (for the Tropez+).

This driver, however, doesn't use the pure firmware as distributed,
but instead relies on a somewhat processed form of it. You can
generate this very easily. Following an idea from Andrew Veliath's
Pinnacle driver, the following flex program will generate the
processed version:

---- cut here -------------------------
%option main
%%
^S[28].*\r$ printf ("%c%.*s", yyleng-1,yyleng-1,yytext);
<<EOF>> { fputc ('\0', stdout); return; }
\n {} 
.  {}
---- cut here -------------------------

To use it, put the above in file (say, ws.l) compile it like this:

      shell> flex -ows.c ws.l
      shell> cc -o ws ws.c
      
and then use it like this:

    ws < my-copy-of-the-oswf.mot-file > /etc/sound/wavefront.os

If you put it somewhere else, you'll always have to use the wf_ospath
module parameter (see below) or alter the source code.

**********************************************************************
7) How do I get it working ?
**********************************************************************

Optionally, you can reboot with the "new" kernel (even though the only
changes have really been made to a module).

Then, as root do:

     modprobe wavefront

You should get something like this in /var/log/messages:

    WaveFront: firmware 1.20 already loaded.

or 

    WaveFront: no response to firmware probe, assume raw.

then:

    WaveFront: waiting for memory configuration ...
    WaveFront: hardware version 1.64
    WaveFront: available DRAM 8191k
    WaveFront: 332 samples used (266 real, 13 aliases, 53 multi), 180 empty
    WaveFront: 128 programs slots in use
    WaveFront: 256 patch slots filled, 142 in use

The whole process takes about 16 seconds, the longest waits being
after reporting the hardware version (during the firmware download),
and after reporting program status (during patch status inquiry).  Its
shorter (about 10 secs) if the firmware is already loaded (i.e. only
warm reboots since the last firmware load).

The "available DRAM" line will vary depending on how much added RAM
your card has. Mine has 8MB.

To check basically functionality, use play(1) or splay(1) to send a
.WAV or other audio file through the audio portion. Then use playmidi
to play a General MIDI file. Try the "-D 0" to hear the
difference between sending MIDI to the WaveFront and using the OPL/3,
which is the default (I think ...). If you have an external synth(s)
hooked to the soundcard, you can use "-e" to route to the
external synth(s) (in theory, -D 1 should work as well, but I think
there is a bug in playmidi which prevents this from doing what it
should). 

**********************************************************************
8) What are the module parameters ?
**********************************************************************

Its best to read wavefront.c for this, but here is a summary:

integers: 
	  wf_raw  - if set, ignore apparent presence of firmware
		    loaded onto the ICS2115, reset the whole
		    board, and initialize it from scratch. (default = 0)

          fx_raw  - if set, always initialize the YSS225 processor
		    on the Tropez plus. (default = 1)

          < The next 4 are basically for kernel hackers to allow
	    tweaking the driver for testing purposes. >		    

          wait_usecs        -  loop timer used when waiting for
			       status conditions on the board. 
			       The default is 150.

          debug_default    - debugging flags. See sound/wavefront.h
			     for WF_DEBUG_* values. Default is zero.
			     Setting this allows you to debug the
			     driver during module installation.
strings:
	  ospath - path to get to the pre-processed OS firmware.
		    (default: /etc/sound/wavefront.os)

**********************************************************************
9) Who should I contact if I have problems?
**********************************************************************

Just me: Paul Barton-Davis <pbd@op.net>